MX8 Basler Camera NXP: Difference between revisions
No edit summary |
No edit summary |
||
| Line 14: | Line 14: | ||
* [https://www.variscite.com/product/accessories/vcam-ar1335b-i-mx8-camera-board/ VCAM-AR1335B] (daA4200-30mci): '''not''' supported | * [https://www.variscite.com/product/accessories/vcam-ar1335b-i-mx8-camera-board/ VCAM-AR1335B] (daA4200-30mci): '''not''' supported | ||
* [https://www.variscite.com/product/accessories/vcam-ar0821b-camera-board/ VCAM-AR0821B] (daA3840-mc): supported | * [https://www.variscite.com/product/accessories/vcam-ar0821b-camera-board/ VCAM-AR0821B] (daA3840-mc): supported | ||
{{#if: {{#var:META_BASLER_NXP_LOCALCONF_SECTION}} | | |||
= Download Variscite Yocto BSP = | = Download Variscite Yocto BSP = | ||
| Line 32: | Line 32: | ||
= Preparing Yocto to use the Basler camera = | = Preparing Yocto to use the Basler camera = | ||
{{#if: {{#var:META_BASLER_NXP_LOCALCONF_SECTION}} || | {{#if: {{#var:META_BASLER_NXP_LOCALCONF_SECTION}} || | ||
There is no need to build a special Yocto image. The default Yocto build, as installed from a standard recovery SD card, already supports the Basler camera.<br> | |||
}} | }} | ||
The Yocto image supports the standard camera by default. | The Yocto image supports the standard camera by default. | ||
Revision as of 11:51, 23 October 2022
Introduction
The following instructions will allow you to add support for the Basler MIPI camera to your Yocto images using the software modules already present in the Yocto BSP.
This will allow you to stream images/video from a Basler camera(s) connected to a Variscite evaluation kit.
Available cameras
- VCAM-AR1335B (daA4200-30mci): not supported
- VCAM-AR0821B (daA3840-mc): supported
Download Variscite Yocto BSP
Please follow Build Yocto from source code.
Execute steps 1-4.3 to download the BSP sources, but don't start bitbake yet.
Customize configuration files
Customize local.conf
Add the following to conf/local.conf under your Yocto build directory:
IMAGE_INSTALL_append_mx8mp = " \
kernel-module-isp-vvcam \
isp-imx \
basler-camera \
"
Build Yocto image
Continue following Build Yocto from source code from where you left off, to bitbake and install an image.
Preparing Yocto to use the Basler camera
The Yocto image supports the standard camera by default. In order to use the Basler camera an additional step is needed. Run the following commands at the shell prompt:
# cd /boot # mv imx8mp-var-dart-dt8mcustomboard.dtb imx8mp-var-dart-dt8mcustomboard-ov5640.dtb # mv imx8mp-var-dart-dt8mcustomboard-legacy.dtb imx8mp-var-dart-dt8mcustomboard-legacy-ov5640.dtb # mv imx8mp-var-som-symphony.dtb imx8mp-var-som-symphony-ov5640.dtb # ln -fs imx8mp-var-dart-dt8mcustomboard-basler-isp0.dtb imx8mp-var-dart-dt8mcustomboard.dtb # ln -fs imx8mp-var-dart-dt8mcustomboard-legacy-basler-isp0.dtb imx8mp-var-dart-dt8mcustomboard-legacy.dtb # ln -fs imx8mp-var-som-symphony-basler-isp0.dtb imx8mp-var-som-symphony.dtb
Running GStreamer
Run the following command at the shell prompt:
$ gst-launch-1.0 -v v4l2src device=/dev/video0 ! waylandsink
Prebuilt recovery SD card image
A prebuilt recovery SD card image with Basler camera support can be downloaded from:
Note: Some web browsers have removed FTP support. Please see our FTP wiki page.