Difference between revisions of "Yocto Build U-Boot"

From Variscite Wiki
(Skip ATF patches if VARISCITE_ATF_GIT set)
Line 98: Line 98:
  
 
Download and build ATF:<!--  
 
Download and build ATF:<!--  
Use IMX_ATF from yocto platform customization if exists for Variscite hosted repo, else default to NXP:
+
Use VARISCITE_ATF_GIT from yocto platform customization if exists for Variscite hosted repo, else default to NXP:
 
-->
 
-->
  $ git clone {{#var:IMX_ATF_GIT | {{#var:NXP_IMX_GIT}}/imx-atf }} -b {{#var:IMX_ATF_BRANCH | {{#var:NXP_IMX_BRANCH}}}}  
+
  $ git clone {{#var:VARISCITE_ATF_GIT | {{#var:NXP_IMX_GIT}}/imx-atf }} -b {{#var:VARISCITE_ATF_BRANCH | {{#var:NXP_IMX_BRANCH}}}}  
 
  {{#ifeq: {{#var:SOC_FAMILY}}|imx8m|
 
  {{#ifeq: {{#var:SOC_FAMILY}}|imx8m|
 
  $ git clone {{#var:META_VARISCITE_GIT}} -b {{#var:META_VARISCITE_BRANCH}}
 
  $ git clone {{#var:META_VARISCITE_GIT}} -b {{#var:META_VARISCITE_BRANCH}}
Line 115: Line 115:
 
  }}
 
  }}
 
  $ cd imx-atf
 
  $ cd imx-atf
 +
{{#if: {{#var:VARISCITE_ATF_GIT}}||
 
  {{#ifeq: {{#var:SOC_FAMILY}}| imx8m |
 
  {{#ifeq: {{#var:SOC_FAMILY}}| imx8m |
 
  {{#ifeq: {{#var:FSL_BSP_VERSION}}| L4.14.78-1.0.0_ga | $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* |
 
  {{#ifeq: {{#var:FSL_BSP_VERSION}}| L4.14.78-1.0.0_ga | $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* |
Line 121: Line 122:
 
  {{#ifeq: {{#var:SOC}}|mx8mm| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8mm* ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-* |
 
  {{#ifeq: {{#var:SOC}}|mx8mm| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8mm* ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-* |
 
  {{#ifeq: {{#var:SOC}}|mx8mq| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-*|}} }} }} }} }} }}
 
  {{#ifeq: {{#var:SOC}}|mx8mq| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-*|}} }} }} }} }} }}
 
+
}}
 
  $ source {{#var:TOOLCHAIN_LOCATION}}
 
  $ source {{#var:TOOLCHAIN_LOCATION}}
 
  $ unset LDFLAGS
 
  $ unset LDFLAGS

Revision as of 22:26, 17 November 2020

Yocto Build U-Boot from source code

1 Toolchain installation for out of Yocto builds

To install the toolchain, follow Yocto Toolchain installation.

2 Build U-Boot out of Yocto tree

Obtain sources:

$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03
$ cd uboot-imx

Configure compilation environment:

$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi

Cleanup everything:

$ make mrproper

Select one of the following configurations:

For booting from SD card/eMMC:
$ make mx6var_som_sd_defconfig

For booting from NAND flash:
$ make mx6var_som_nand_defconfig

Build U-Boot:

$ make -j4


3 Install the built U-Boot on an SD card


$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync
$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync
(Replace /dev/sdX with the correct device)

If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:

$ sudo cp SPL /media/rootfs/opt/images/... 
$ sudo cp u-boot.img /media/rootfs/opt/images/...

And eject the SD card gracefully from host machine.


Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)

4 Update your U-Boot out of Yocto tree

$ git pull