Difference between revisions of "Yocto Build U-Boot"

From Variscite Wiki
m (1 revision imported: Import of additions after the 20th of May 2020)
Line 134: Line 134:
  
 
{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
 
{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
 +
{{#ifeq: {{#var:SOC}}|mx8qxp|
 +
Build boot image for B0 SOC revision:
 +
$ make -f soc.mak clean
 +
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} REV=B0 MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl
 +
$ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
 +
<br>
 +
Build boot image for C0 SOC revision:
 +
$ make -f soc.mak clean
 +
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} REV=C0 MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl
 +
$ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
 +
|
 
Build boot image:
 
Build boot image:
 
  $ make -f soc.mak clean
 
  $ make -f soc.mak clean
 
  $ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl
 
  $ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl
 
  $ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
 
  $ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
 +
}}
 
|
 
|
 
{{#ifeq: {{#var:SOC}}|mx8mq|
 
{{#ifeq: {{#var:SOC}}|mx8mq|

Revision as of 13:43, 15 June 2020

Yocto Build U-Boot from source code

1 Toolchain installation for out of Yocto builds

To install the toolchain, follow Yocto Toolchain installation.

2 Build U-Boot out of Yocto tree

Obtain sources:

$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03
$ cd uboot-imx

Configure compilation environment:

$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi

Cleanup everything:

$ make mrproper

Select one of the following configurations:

For booting from SD card/eMMC:
$ make mx6var_som_sd_defconfig

For booting from NAND flash:
$ make mx6var_som_nand_defconfig

Build U-Boot:

$ make -j4


3 Install the built U-Boot on an SD card


$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync
$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync
(Replace /dev/sdX with the correct device)

If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:

$ sudo cp SPL /media/rootfs/opt/images/... 
$ sudo cp u-boot.img /media/rootfs/opt/images/...

And eject the SD card gracefully from host machine.


Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)

4 Update your U-Boot out of Yocto tree

$ git pull