DART-MX8M Display

From Variscite Wiki
Revision as of 22:31, 3 May 2021 by Pierluigi (talk | contribs)
DART-MX8M Display



I.MX8M supports MIPI-DSI, HDMI and DP displays. DART-MX8M can be optionally equipped with SN65DSI84 MIPI-DSI to LVDS bridge.
DART-MX8M carrier board comes with LVDS, HDMI and DP connectors, so you can connect LVDS, HDMI or DP display.
Dual LVDS+HDMI or LVDS+DP display configurations are also supported.
Connecting MIPI-DSI display to DART-MX8M carrier board requires designing a custom connector.


i.MX8M comes with 2 display controllers: DCSS and LCDIF.
DCCS can be connected to HDMI, DP or MIPI-DSI and supports resolutions up to 4K.
LCDIF can be connected only to MIPI-DSI and supports resolutions up to 1080p.

Selecting display configuration

Selecting display configuration is a matter of selecting an appropriate DTB file.
All available DTB files are listed in the table below.

DTB File Name
fsl-imx8mq-var-dart-emmc-wifi-hdmi.dtb Device tree blob for eMMC, WIFI and HDMI display configuration. SD card disabled.
fsl-imx8mq-var-dart-emmc-wifi-lvds.dtb Device tree blob for eMMC, WIFI and LVDS display configuration. SD card disabled.
fsl-imx8mq-var-dart-emmc-wifi-dual-display.dtb Device tree blob for eMMC, WIFI and dual LVDS+HDMI display configuration. SD card disabled.
fsl-imx8mq-var-dart-sd-emmc-hdmi.dtb Device tree blob for SD, eMMC and HDMI display configuration. WIFI disabled.
fsl-imx8mq-var-dart-sd-emmc-lvds.dtb Device tree blob for SD, eMMC and LVDS display configuration. WIFI disabled.
fsl-imx8mq-var-dart-sd-emmc-dual-display.dtb Device tree blob for SD, eMMC and dual LVDS+HDMI display configuration. WIFI disabled.

File /boot/fsl-imx8mq-var-dart.dtb is a symbolic link to the active DTB file. By default LVDS display is used.
For example, to select HDMI display in WIFI configuration, run the following commands:

# cd /boot
# ln -fs fsl-imx8mq-var-dart-wifi-hdmi.dtb fsl-imx8mq-var-dart.dtb

Reboot is required for new configuration to take effect.

Setting HDMI display resolution

By default the maximum resolution supported by HDMI display is used.

To check the current resolution, use fbset command:

root@imx8m-var-dart:~# fbset

mode "1920x1080"
    geometry 1920 1080 1920 1080 32
    timings 0 0 0 0 0 0 0
    accel true
    rgba 8/16,8/8,8/0,0/0

To modify HDMI display resolution use fw_setenv command to set "video" kernel parameter.
For example, to set 1080P@60fps resolution, run

# fw_setenv kernelargs video=HDMI-A-1:1920x1080-32@60

The setting will take effect after reboot.

Setting Weston desktop resolution

The default Weston desktop resolution is 1080P. This setting is independent of actual display resolution.
To modify Weston resolution, edit /etc/xdg/weston/weston.ini and set size parameter in shell section.
For example, to set 4K resolution


For new setting to take effect restart weston by running

# systemctl restart weston

Dual display configuration

In dual display configuration Weston desktop is running on LVDS display and HDMI display is blank.
To play video on HDMI display the following command can be used:

# gplay-1.0 --video-sink=kmssink video.mp4

To play video on LVDS display the following command can be used:

# gplay-1.0 --video-sink=waylandsink video.mp4

Adding custom LVDS panel

DART-MX8M evaluation kit comes with 800x480 LCD panel. DART-MX8M DTS files were created with this panel in mind. To support your custom LVDS panel, you should make several modifications

The following code references Variscite panel in arch/arm64/boot/dts/freescale/fsl-imx8mq-var-dart-common.dtsi under kernel source tree

	dsi_lvds_bridge: sn65dsi84@2c {
		compatible = "ti,sn65dsi83";
		reg = <0x2c>;
		ti,dsi-lanes = <1>;
		ti,lvds-format = <1>;
		ti,lvds-bpp = <24>;
		ti,width-mm = <154>;
		ti,height-mm = <87>;
		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_lvds>;
		status = "okay";

		display-timings {
			lvds {
				clock-frequency = <33000000>;
				hactive = <800>;
				vactive = <480>;
				hback-porch = <40>;
				hfront-porch = <40>;
				vback-porch = <29>;
				vfront-porch = <13>;
				hsync-len = <48>;
				vsync-len = <3>;
				hsync-active = <0>;
				vsync-active = <0>;
				de-active = <1>;
				pixelclk-active = <0>;

You should modify "ti,dsi-lanes", "ti,lvds-format", "ti,lvds-bpp", "ti,width-mm", "ti,height-mm" and "display-timings" properties to match your panel specification and rebuild the DTB file.
To support dual channel LVDS panel, please add "ti,lvds-channels = <2>" property. Also, for dual channel LVDS panels clock frequency and horizontal parameters mentioned in panel datasheet should be doubled.