Android UUU IMX8
UUU (Universal Update Utility) is an open source utility by NXP that allows downloading and executing code on i.MX SoCs through the Serial Download Protocol (SDP).
It is the next generation of NXP's MFGTOOL used to load SPL and U-Boot via the USB OTG port and optionally program the internal storage of the SOM.
For more details please visit https://github.com/NXPmicro/mfgtools
All Variscite SOMs are shipped with U-Boot pre-programmed on the internal storage.
In addition, all Variscite carrier boards have an SD card slot, and even in the unlikely event of the U-Boot being erased from the internal storage, the SOM can always be booted from an SD card (like our recovery SD card, for example).
2 Step by step usage instructions
Download and build uuu:
$ sudo apt-get install libusb-1.0-0-dev libzip-dev libbz2-dev pkg-config cmake $ cd ~ $ git clone https://github.com/NXPmicro/mfgtools.git $ cd mfgtools $ git checkout uuu_1.4.240 $ cmake . $ make
Preparing UUU for Android flashing:
- Android build outputs the U-Boot using the defconfig for SD card/eMMC by default.
- Copy the uuu binary to the Android build output folder:
$ cp ~/mfgtools/uuu/uuu ~/var_imx-android-11.0.0_1.0.0/android_build/out/target/product/dart_mx8mm
Boot the board into serial download mode:
- Set the board boot mode to SD card, while not having an actual card inserted in its slot.
Alternatively, set the board boot mode to eMMC/NAND flash, when the eMMC/NAND flash does not contain a bootloader.
Connect the board to your host PC via the USB OTG port, and power on the board.
The board should be recognized on the host as a "NXP Semiconductors SE Blank M850" (or something similar).
If your board only has a regular USB type-A connector and doesn't have a USB Micro-AB or Type-C receptacle, you can use a "male USB type-A to male USB type-A" cable.
Use UUU to program Android to the eMMC:
Copy Variscite's uuu scripts to the Android build output folder:
$ cp ~/var_imx-android-11.0.0_1.0.0/android_build/device/variscite/scripts/uuu_scripts/* out/target/product/dart_mx8mm/
And run uuu to program the eMMC:
$ sudo ./uuu <uuu script>.lst
where <uuu script> should be one of the following:
emmc_burn_android_imx8mm_var_dart_dt8mcustomboard.lst - Supports LVDS / SD / WiFi (DART-MX8M-MINI on DT8MCustomBoard 2.x) emmc_burn_android_imx8mm_var_dart_dt8mcustomboard_legacy.lst - Supports LVDS / SD / WiFi (DART-MX8M-MINI on DT8MCustomBoard 1.x) emmc_burn_android_imx8mm_var_som_symphony.lst - Supports LVDS / SD / WiFi (VAR-SOM-MX8M-MINI on a Symphony-Board V1.4A and above) emmc_burn_android_imx8mm_var_som_symphony_legacy.lst - Supports LVDS / SD / WiFi (VAR-SOM-MX8M-MINI on a Symphony-Board V1.4 and below)
You can see its output on the console via the debug port, as always.
After flashing is complete without errors, set the DIP switch back to eMMC and power cycle the board.
- For m7/m4 dtbs change the postfix with -m4/-m7 respectively in the .lst files
- By default the partition table is specified by partition-table.img, which is for a 16GB eMMC.
If you wish to use a 32GB eMMC, edit the respective .lst file and replace partition-table.img with partition-table-28GB.img.