Variscite's FTP

The Variscite's FTP directory tree is as following:

dart-sd410
├── Software
│   ├── Android
│   │   ├── LL.1.2.4-01810-8x16.0-3
│   │   ├── ...
│   │   └── RescueImages
│   ├── Yocto
│   │   ├── ...
│   │   └── RescueImages
│   ├── Ubuntu
│   │   ├── ...
│   │   └── RescueImages
│   ├── Windows
│   │   ├── ...
│   │   └── RescueImages
│   └── EmmcRecovery
└── Hardware
    ├── Schematics
    ├── Datasheets
    └── Layout

dart-sd410 -> Software -> EmmcRecovery directory contains a recovery SD Card image for switching OSes and Recovery
dart-sd410 -> Software -> OS -> RescueImages directory contains prebuilt last version of the system together with partition table file and boot loaders.

NOTE:
Please refer to support@variscite.com for obtaining FTP credentials.

NOTE:

The partition table file and bootloaders are supplied in binary format and cannot be altered by the customers.

Please contact variscite support for changes.

Switching between OSes

Download the rescue SD Card Image (DART-SD410_sd_rescue.img) from Variscite's FTP site. It is located in dart-sd410 -> Software -> RescueDiskImage directory
Download the rescue images of the new OS from Variscite's FTP site. The latest version located in dart-sd410 -> Software -> New OS -> RescueImages

Preparing rescue SD-Card

Plug your SD card to your Linux machine, run dmesg and see what device is added (i.e. /dev/sdX)

Run the following command to write the image file to the SD card

$ sudo dd if=~/Downloads/DART-SD410_sd_rescue.img of=/dev/sdX bs=128k
Change the /dev/sdX with your SD card device.

After the write process is finished run
$ sudo sync

Remove the SD card from your PC and insert it into the SD card slot of the VAR-SD410CustomBoard
Set Boot Select switch (SW3) to the ON position. This directs the DART-SD410 to boot from an external SD card.
Cycle the power of the VAR-SD410CustomBoard

After this step the system will read the image from external SD card and boot into a fastboot mode.
Now you are ready to update the OS to the latest version.

Navigate to the downloaded RescueImages folder of the chosen OS
Run flashall script
Set Boot Select switch (SW3) to the OFF position. This tells the DART-SD410 to boot from internal eMMC device.
Cycle the power of the VAR-SD410CustomBoard

The needed OS will start

Start using your VAR-SD410CustomBoard

Upack the contents of the package
Veryfy that the DART-SD410 SoM is connected properly into VAR-SD410CustomBoard card
Connect the screen LVDS cable to the LCD (the red wires should be at pin 1 position)
Connect the other side of the cable to VAR-SD410CustomBoard J11 (the red wires should be at pin 1 position i.e. closer to HDMI connector)
Connect the touch screen flat cable to J4 (the copper contacts should face PCB card)
Connect USB cable to a PC
Connect the Micro USB plug to VAR-SD410CustomBoard J21. Wait for USB device enumeration and driver installation
Open any serial port console program (we suggest using Putty) and set it to 115200,8,1,n baudrate
Plug in the power supply to 100/220V

NOTE:
If Camera adapter was purchased then it should be plugged in before the first power up. Otherwise the Android will remove Camera program and it will not be accessible untill system re-flash

Plug in the power adapter 5V to VAR-SD410CustomBoard J18

Immideately the serial console will show the booting process and after about a minute the LCD will show the boot animation and Android will be started

NOTE:
The first Boot up of the Android takes more time because of database initialization

NOTE:
Please remove SD card from the slop before boot

Switching display options in Android

To switch between LCD and HDMI the following fastboot commands should be run

To switch to HDMI

$ fastboot oem select-display-panel adv7533_1080p

To switch to LCD

$ fastboot oem select-display-panel

DART-SD410 Android Getting Started

Contents