Debian Platform Customization

Debian

Documentation

Stretch 9

• Debian 9 - Stretch (released on 06/17/2017)

Documentation is available from wiki.debian.org

VAR-SOM-MX6

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
uImage	Linux kernel image
SPL.nand	SPL built for NAND. The SPL is pre-U-Boot SW component, required for DDR initialization
SPL.emmc	SPL built for SD card and eMMC boot. The SPL is pre-U-Boot SW component, required for DDR initialization
u-boot.img.nand	U-Boot built for NAND flash
u-boot.img.mmc	U-Boot built for SD card or eMMC boot
Device Tree name	Details
imx6dl-var-som-solo-cap.dtb	VAR-SOM-SOLO with iMX6S/DL on MX6CustomBoard with capacitive touch
imx6dl-var-som-solo-res.dtb	VAR-SOM-SOLO with iMX6S/DL on MX6CustomBoard with resistive touch
imx6dl-var-som-solo-vsc.dtb	VAR-SOM-SOLO with iMX6S/DL on SOLOCustomBoard with capacitive touch
imx6dl-var-som-cap.dtb	VAR-SOM-MX6 with iMX6S/DL on MX6CustomBoard with capacitive touch
imx6dl-var-som-res.dtb	VAR-SOM-MX6 with iMX6S/DL on MX6CustomBoard with resistive touch
imx6dl-var-som-vsc.dtb	VAR-SOM-MX6 with iMX6S/DL on SOLOCustomBoard with capacitive touch
imx6q-var-som-cap.dtb	VAR-SOM-MX6 with iMX6D/Q on MX6CustomBoard with capacitive touch
imx6q-var-som-res.dtb	VAR-SOM-MX6 with iMX6D/Q on MX6CustomBoard with resistive touch
imx6q-var-som-vsc.dtb	VAR-SOM-MX6 with iMX6D/Q on SOLOCustomBoard with capacitive touch
imx6qp-var-som-cap.dtb	VAR-SOM-MX6 with iMX6DP/QP on MX6CustomBoard with capacitive touch
imx6qp-var-som-res.dtb	VAR-SOM-MX6 with iMX6DP/QP on MX6CustomBoard with resistive touch
imx6qp-var-som-vsc.dtb	VAR-SOM-MX6 with iMX6DP/QP on SOLOCustomBoard with capacitive touch
imx6q-var-dart.dtb	DART-MX6 with iMX6D/Q on DARTCustomBoard with capacitive touch

DART-6UL

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
rootfs.ubi.img	Use for flash to NAND
zImage	Linux kernel image
SPL.nand	SPL built for NAND. The SPL is pre-U-Boot SW component, required for DDR initialization
SPL.emmc	SPL built for SD card and eMMC boot. The SPL is pre-U-Boot SW component, required for DDR initialization
u-boot.img.nand	U-Boot built for NAND flash
u-boot.img.emmc	U-Boot built for SD card or eMMC
Device Tree name	Details
imx6ul-var-dart-emmc_wifi.dtb	DART-6UL with eMMC and WiFi enabled. (SD card & NAND disabled)
imx6ul-var-dart-nand_wifi.dtb	DART-6UL with l NAND and WiFi enabled. (SD card & eMMC disabled)
imx6ul-var-dart-sd_emmc.dtb	DART-6UL with SD card and eMMC enabled (WiFi & NAND disabled). You can boot from eMMC or SD card
imx6ul-var-dart-sd_nand.dtb	DART-6UL with SD card and NAND enabled (WiFi & eMMC disabled). You can boot from NAND or SD card
imx6ul-var-dart-5g-emmc_wifi.dtb	DART-6UL-5G with eMMC and WiFi enabled. (SD card & NAND disabled)
imx6ul-var-dart-5g-nand_wifi.dtb	DART-6UL-5G with l NAND and WiFi enabled. (SD card & eMMC disabled)
imx6ull-var-dart-emmc_wifi.dtb	DART-6ULL with eMMC and WiFi enabled. (SD card & NAND disabled)
imx6ull-var-dart-nand_wifi.dtb	DART-6ULL with l NAND and WiFi enabled. (SD card & eMMC disabled)
imx6ull-var-dart-sd_emmc.dtb	DART-6ULL with SD card and eMMC enabled (WiFi & NAND disabled). You can boot from eMMC or SD card
imx6ull-var-dart-sd_nand.dtb	DART-6ULL with SD card and NAND enabled (WiFi & eMMC disabled). You can boot from NAND or SD card
imx6ull-var-dart-5g-emmc_wifi.dtb	DART-6ULL-5G with eMMC and WiFi enabled. (SD card & NAND disabled)
imx6ull-var-dart-5g-nand_wifi.dtb	DART-6ULL-5G with l NAND and WiFi enabled. (SD card & eMMC disabled)

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
rootfs.ubi.img	Use for flash to NAND
zImage	Linux kernel image
SPL.nand	SPL built for NAND. The SPL is pre-U-Boot SW component, required for DDR initialization
SPL.mmc	SPL built for SD card and eMMC boot. The SPL is pre-U-Boot SW component, required for DDR initialization
u-boot.img.nand	U-Boot built for NAND flash
u-boot.img.mmc	U-Boot built for SD card or eMMC
Device Tree name	Details
imx6ull-var-dart-6ulcustomboard-emmc-sd-card.dtb	Device tree blob for DART-6UL with i.MX6ULL SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ull-var-dart-6ulcustomboard-emmc-wifi.dtb	Device tree blob for DART-6UL with i.MX6ULL SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ull-var-dart-6ulcustomboard-nand-sd-card.dtb	Device tree blob for DART-6UL with i.MX6ULL SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ull-var-dart-6ulcustomboard-nand-wifi.dtb	Device tree blob for DART-6UL with i.MX6ULL SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)
imx6ul-var-dart-6ulcustomboard-emmc-sd-card.dtb	Device tree blob for DART-6UL with i.MX6UL SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ul-var-dart-6ulcustomboard-emmc-wifi.dtb	Device tree blob for DART-6UL with i.MX6UL SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ul-var-dart-6ulcustomboard-nand-sd-card.dtb	Device tree blob for DART-6UL with i.MX6UL SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ul-var-dart-6ulcustomboard-nand-wifi.dtb	Device tree blob for DART-6UL with i.MX6UL SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)
imx6ulz-var-dart-6ulcustomboard-emmc-sd-card.dtb	Device tree blob for DART-6UL with i.MX6ULZ SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ulz-var-dart-6ulcustomboard-emmc-wifi.dtb	Device tree blob for DART-6UL with i.MX6ULZ SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ulz-var-dart-6ulcustomboard-nand-sd-card.dtb	Device tree blob for DART-6UL with i.MX6ULZ SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ulz-var-dart-6ulcustomboard-nand-wifi.dtb	Device tree blob for DART-6UL with i.MX6ULZ SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)
imx6ull-var-som-concerto-board-emmc-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULL SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ull-var-som-concerto-board-emmc-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULL SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ull-var-som-concerto-board-nand-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULL SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ull-var-som-concerto-board-nand-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULL SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)
imx6ul-var-som-concerto-board-emmc-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6UL SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ul-var-som-concerto-board-emmc-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6UL SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ul-var-som-concerto-board-nand-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6UL SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ul-var-som-concerto-board-nand-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6UL SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)
imx6ulz-var-som-concerto-board-emmc-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULZ SOC, eMMC & SD card enabled. (NAND flash & WiFi disabled)
imx6ulz-var-som-concerto-board-emmc-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULZ SOC, eMMC & WiFi enabled. (NAND flash & SD card disabled)
imx6ulz-var-som-concerto-board-nand-sd-card.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULZ SOC, NAND flash & SD card enabled. (eMMC & WiFi disabled)
imx6ulz-var-som-concerto-board-nand-wifi.dtb	Device tree blob for VAR-SOM-6UL with i.MX6ULZ SOC, NAND flash & WiFi enabled. (eMMC & SD card disabled)

SD card image file tree

/opt/images/
└── Debian
    ├── imx6ul-var-dart-5g-emmc_wifi.dtb
    ├── imx6ul-var-dart-5g-nand_wifi.dtb
    ├── imx6ul-var-dart-emmc_wifi.dtb
    ├── imx6ul-var-dart-nand_wifi.dtb
    ├── imx6ul-var-dart-sd_emmc.dtb
    ├── imx6ul-var-dart-sd_nand.dtb
    ├── imx6ull-var-dart-5g-emmc_wifi.dtb
    ├── imx6ull-var-dart-5g-nand_wifi.dtb
    ├── imx6ull-var-dart-emmc_wifi.dtb
    ├── imx6ull-var-dart-nand_wifi.dtb
    ├── imx6ull-var-dart-sd_emmc.dtb
    ├── imx6ull-var-dart-sd_nand.dtb
    ├── rootfs.tar.gz
    ├── rootfs.ubi.img
    ├── SPL.mmc
    ├── SPL.nand
    ├── u-boot.img.mmc
    ├── u-boot.img.nand
    └── zImage

/opt/images/
└── Yocto
    ├── imx6ull-var-dart-6ulcustomboard-emmc-sd-card.dtb
    ├── imx6ull-var-dart-6ulcustomboard-emmc-wifi.dtb
    ├── imx6ull-var-dart-6ulcustomboard-nand-sd-card.dtb
    ├── imx6ull-var-dart-6ulcustomboard-nand-wifi.dtb
    ├── imx6ull-var-som-concerto-board-emmc-sd-card.dtb
    ├── imx6ull-var-som-concerto-board-emmc-wifi.dtb
    ├── imx6ull-var-som-concerto-board-nand-sd-card.dtb
    ├── imx6ull-var-som-concerto-board-nand-wifi.dtb
    ├── imx6ul-var-dart-6ulcustomboard-emmc-sd-card.dtb
    ├── imx6ul-var-dart-6ulcustomboard-emmc-wifi.dtb
    ├── imx6ul-var-dart-6ulcustomboard-nand-sd-card.dtb
    ├── imx6ul-var-dart-6ulcustomboard-nand-wifi.dtb
    ├── imx6ul-var-som-concerto-board-emmc-sd-card.dtb
    ├── imx6ul-var-som-concerto-board-emmc-wifi.dtb
    ├── imx6ul-var-som-concerto-board-nand-sd-card.dtb
    ├── imx6ul-var-som-concerto-board-nand-wifi.dtb
    ├── imx6ulz-var-dart-6ulcustomboard-emmc-sd-card.dtb
    ├── imx6ulz-var-dart-6ulcustomboard-emmc-wifi.dtb
    ├── imx6ulz-var-dart-6ulcustomboard-nand-sd-card.dtb
    ├── imx6ulz-var-dart-6ulcustomboard-nand-wifi.dtb
    ├── imx6ulz-var-som-concerto-board-emmc-sd-card.dtb
    ├── imx6ulz-var-som-concerto-board-emmc-wifi.dtb
    ├── imx6ulz-var-som-concerto-board-nand-sd-card.dtb
    ├── imx6ulz-var-som-concerto-board-nand-wifi.dtb
    ├── rootfs.tar.gz
    ├── rootfs.ubi.img
    ├── SPL.mmc
    ├── SPL.nand
    ├── u-boot.img.mmc
    ├── u-boot.img.nand
    └── zImage

VAR-SOM-MX7

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
rootfs.ubi.img	Use for flash to nand
zImage	Linux kernel image
SPL.nand	SPL built for NAND. The SPL is pre-U-Boot SW component, required for DDR initialization
SPL.emmc	SPL built for SD card and eMMC boot. The SPL is pre-U-Boot SW component, required for DDR initialization
u-boot.img.nand	U-Boot built for NAND flash
u-boot.img.emmc	U-Boot built for SD card or eMMC boot
Device Tree name	Details
imx7d-var-som-emmc.dtb	Boot from SD or eMMC
imx7d-var-som-nand.dtb	Boot from NAND
imx7d-var-som-emmc-m4.dtb	Boot from SD or eMMC with M4 support
imx7d-var-som-nand-m4.dtb	Boot from NAND with M4 support

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
rootfs.ubi.img	Use for flash to nand
zImage	Linux kernel image
SPL.nand	SPL built for NAND. The SPL is pre-U-Boot SW component, required for DDR initialization
SPL.mmc	SPL built for SD card and eMMC boot. The SPL is pre-U-Boot SW component, required for DDR initialization
u-boot.img.nand	U-Boot built for NAND flash
u-boot.img.mmc	U-Boot built for SD card or eMMC boot
Device Tree name	Details
imx7d-var-som-emmc.dtb	Boot from SD or eMMC
imx7d-var-som-nand.dtb	Boot from NAND
imx7d-var-som-emmc-m4.dtb	Boot from SD or eMMC with M4 support
imx7d-var-som-nand-m4.dtb	Boot from NAND with M4 support

DART-MX8M

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
Image.gz	Linux kernel image
imx-boot-sd.bin	U-Boot built for SD card and eMMC
Device Tree name	Details
fsl-imx8mq-var-dart-emmc-wifi-dual-display.dtb	DART-MX8M with HDMI+LVDS, eMMC and WiFi (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-hdmi.dtb	DART-MX8M with HDMI, eMMC and WiFi (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-lvds.dtb	DART-MX8M with LVDS, eMMC and WiFi (SD card disabled)
fsl-imx8mq-var-dart-sd-emmc-dual-display.dtb	DART-MX8M with HDMI+LVDS, eMMC and SD (WiFi card disabled)
fsl-imx8mq-var-dart-sd-emmc-hdmi.dtb	DART-MX8M with HDMI, eMMC and SD (WiFi card disabled)
fsl-imx8mq-var-dart-sd-emmc-lvds.dtb	DART-MX8M with LVDS, eMMC and SD (WiFi card disabled)

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
Image.gz	Linux kernel image
imx-boot-sd.bin	U-Boot built for SD card and eMMC
Device Tree name	Details
fsl-imx8mq-var-dart-emmc-wifi-hdmi.dtb	DART-MX8M with eMMC, WIFI and HDMI display configuration on carrier board revisions 1.3 and higher.(SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-lvds.dtb	DART-MX8M with eMMC, WIFI and LVDS display configuration on carrier board revisions 1.3 and higher. (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-dual-display.dtb	DART-MX8M with eMMC, WIFI and dual LVDS+HDMI display configuration on carrier board revisions 1.3 and higher. (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-hdmi-cb12.dtb	DART-MX8M with eMMC, WIFI and HDMI display configuration on carrier board revisions 1.1 and 1.2. (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-lvds-cb12.dtb	DART-MX8M with eMMC, WIFI and LVDS display configuration on carrier board revisions 1.1 and 1.2. (SD card disabled)
fsl-imx8mq-var-dart-emmc-wifi-dual-display-cb12.dtb	DART-MX8M with eMMC, WIFI and dual LVDS+HDMI display configuration on carrier board revisions 1.1 and 1.2. (SD card disabled)
fsl-imx8mq-var-dart-sd-emmc-hdmi.dtb	DART-MX8M with SD, eMMC and HDMI display configuration on carrier board revisions 1.3 and higher. (WIFI disabled)
fsl-imx8mq-var-dart-sd-emmc-lvds.dtb	DART-MX8M with SD, eMMC and LCDIF LVDS display configuration on carrier board revisions 1.3 and higher. (WIFI disabled)
fsl-imx8mq-var-dart-sd-emmc-dual-display.dtb	DART-MX8M with SD, eMMC and dual LVDS+HDMI display configuration on carrier board revisions 1.3 and higher. (WIFI disabled)
fsl-imx8mq-var-dart-sd-emmc-hdmi-cb12.dtb	DART-MX8M with SD, eMMC and HDMI display configuration on carrier board revisions 1.1 and 1.2. (WIFI disabled)
fsl-imx8mq-var-dart-sd-emmc-lvds-cb12.dtb	DART-MX8M with SD, eMMC and LCDIF LVDS display configuration on carrier board revisions 1.1 and 1.2. (WIFI disabled)
fsl-imx8mq-var-dart-sd-emmc-dual-display-cb12.dtb	DART-MX8M with SD, eMMC and dual LVDS+HDMI display configuration on carrier board revisions 1.1 and 1.2. (WIFI disabled)

DART-MX8M-MINI

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
Image.gz	Linux kernel image
imx-boot-sd.bin	U-Boot built for SD card and eMMC
Device Tree name	Details
fsl-imx8mm-var-dart.dtb	Device tree blob for SD, eMMC, WIFI and LVDS display configuration.

VAR-SOM-MX8X

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
Image.gz	Linux kernel image
imx-boot-sd.bin	U-Boot built for SD card and eMMC
Device Tree name	Details
fsl-imx8qxp-var-som-wifi.dtb	Device tree blob for eMMC, WIFI and LVDS display configuration.
fsl-imx8qxp-var-som-sd.dtb	Device tree blob for SD, eMMC and LVDS display configuration.

VAR-SOM-MX8

Build Results

The resulted images are located in /output/.

Image name	How to use
rootfs.tar.gz	Root filesystem tarball used for installation on SD card and eMMC
Image.gz	Linux kernel image
imx-boot-sd.bin	U-Boot built for SD card and eMMC
Device Tree name	Details
fsl-imx8qm-var-som-dp.dtb	Device tree blob for VAR-SOM-MX8 with DP display
fsl-imx8qm-var-som-hdmi.dtb	Device tree blob for VAR-SOM-MX8 with HDMI display
fsl-imx8qm-var-som-lvds.dtb	Device tree blob for VAR-SOM-MX8 with LVDS display
fsl-imx8qm-var-spear-dp.dtb	Device tree blob for SPEAR-MX8 with DP display
fsl-imx8qm-var-spear-hdmi.dtb	Device tree blob for SPEAR-MX8 with HDMI display
fsl-imx8qm-var-spear-lvds.dtb	Device tree blob for SPEAR-MX8 with LVDS display

Platform Customizations

VAR-SOM-MX6

stretch-4.9.11-mx6-v1.0

• RELEASE_NAME = stretch-4.9.11-mx6-v1.0
• RELEASE_LINK = RELEASE_STRETCH_V1.0_VAR-SOM-MX6
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.9.11-mx6-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX6/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTaKepnaAwm1umGw59L0ukHEa6VIIlEM9btCiWaXW0jx3nOQmwJ3h2QxyBbH2nMEwmDC_GvFbowtonR/pubhtml
• MACHINE_NAME = var-som-mx6
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.11_1.0.0_ga-var01
• KERNEL_IMAGE = uImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• KERNEL_BUILD_PARAMS = LOADADDR=0x10008000
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6var_som_sd_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6var_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx6_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX6_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX6_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX6_DTB
• SD_TREE_SECTION = VAR-SOM-MX6_SD_TREE
• DEBIAN_FLASH_SD_FROM_GUI_SECTION = VAR-SOM-MX6_FLASH_SD_FROM_GUI
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX6
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• NAND_ROOTFS_DEV = mtd3
• RAM_LOAD_ADDRESS = 0x18100000
• UBOOT_CONFIG_FILE = include/configs/mx6var_som.h
• UBOOT_PAD_SIZE = 0x1e0000
• KERNEL_PAD_SIZE = 0x800000
• DTB_START_ADDRESS = 0x3e0000

stretch-4.9.88-mx6-v2.0

• RELEASE_NAME = stretch-4.9.88-mx6-v2.0
• RELEASE_LINK = RELEASE_STRETCH_V2.0_VAR-SOM-MX6
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.5
• RECOVERY_SD_NAME = stretch-4.9.88-mx6-v2.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX6/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTaKepnaAwm1umGw59L0ukHEa6VIIlEM9btCiWaXW0jx3nOQmwJ3h2QxyBbH2nMEwmDC_GvFbowtonR/pubhtml
• MACHINE_NAME = var-som-mx6
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.88_2.0.0_ga-var01
• KERNEL_IMAGE = uImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• KERNEL_BUILD_PARAMS = LOADADDR=0x10008000
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6var_som_sd_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6var_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx6_var02
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX6_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX6_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX6_DTB
• SD_TREE_SECTION = VAR-SOM-MX6_SD_TREE
• DEBIAN_FLASH_SD_FROM_GUI_SECTION = VAR-SOM-MX6_FLASH_SD_FROM_GUI
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX6
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• NAND_ROOTFS_DEV = mtd3
• RAM_LOAD_ADDRESS = 0x18100000
• UBOOT_CONFIG_FILE = include/configs/mx6var_som.h
• UBOOT_PAD_SIZE = 0x1e0000
• KERNEL_PAD_SIZE = 0x800000
• DTB_START_ADDRESS = 0x3e0000

DART-6UL

stretch-4.9.11-mx6ul-v1.0

• RELEASE_NAME = stretch-4.9.11-mx6ul-v1.0
• RELEASE_LINK = RELEASE_STRETCH_V1.0_DART-6UL
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.9.11-mx6ul-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-6UL/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTUPjdt-nbNyWUFxjrkoIw4H-s1h5Uo3HYgYQvzHgL1SMIutt7fzGm1zq5vgwLQhNAb7fTqETSjBn2J/pubhtml
• MACHINE_NAME = imx6ul-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.11_1.0.0_ga-var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6ul_var_dart_mmc_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6ul_var_dart_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx6ul_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-6UL_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-6UL_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-6UL_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-6UL_SD_TREE
• EMMC_FAT_PARTITION_NAME = BOOT-VAR6UL
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

stretch-4.9.88-mx6ul-v2.0

• RELEASE_NAME = stretch-4.9.88-mx6ul-v2.0
• RELEASE_LINK = RELEASE_STRETCH_V2.0_DART-6UL
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.9.88-mx6ul-v2.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-6UL/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTUPjdt-nbNyWUFxjrkoIw4H-s1h5Uo3HYgYQvzHgL1SMIutt7fzGm1zq5vgwLQhNAb7fTqETSjBn2J/pubhtml
• MACHINE_NAME = imx6ul-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.88_2.0.0_ga-var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6ul_var_dart_mmc_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6ul_var_dart_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx6ul_var02
• DEBIAN_BUILD_RESULTS_SECTION = DART-6UL_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-6UL_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-6UL_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-6UL_SD_TREE
• EMMC_FAT_PARTITION_NAME = BOOT-VAR6UL
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

stretch-4.14.78-mx6ul-v1.0

• RELEASE_NAME = stretch-4.14.78-mx6ul-v1.0
• RELEASE_LINK = RELEASE_STRETCH_V3.0_DART-6UL
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.14.78-mx6ul-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-6UL/Software/debian
• RELEASE_NOTES_LINK = '
• MACHINE_NAME = imx6ul-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6ul_var_dart_mmc_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6ul_var_dart_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx6ul_var03
• DEBIAN_BUILD_RESULTS_SECTION = DART-6UL_BUILD_RESULTS_STRETCH_V3_PLUS
• DEBIAN_BOOT_BOARD_SECTION = DART-6UL_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-6UL_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-6UL_SD_TREE_STRETCH_V3_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR6UL
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx6ul-v1.0

• RELEASE_NAME = buster-4.14.78-mx6ul-v1.0
• RELEASE_LINK = RELEASE_BUSTER_V1.0_DART-6UL
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = buster-4.14.78-mx6ul-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-6UL/Software/debian
• RELEASE_NOTES_LINK = '
• MACHINE_NAME = imx6ul-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6ul_var_dart_mmc_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6ul_var_dart_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-6UL_BUILD_RESULTS_STRETCH_V3_PLUS
• DEBIAN_BOOT_BOARD_SECTION = DART-6UL_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-6UL_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-6UL_SD_TREE_STRETCH_V3_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR6UL
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx6ul-v1.1

• RELEASE_NAME = buster-4.14.78-mx6ul-v1.1
• RELEASE_LINK = RELEASE_BUSTER_V1.1_DART-6UL
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = buster-4.14.78-mx6ul-v1.1.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-6UL/Software/debian
• RELEASE_NOTES_LINK = '
• MACHINE_NAME = imx6ul-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx6ul_var_dart_mmc_defconfig
• U-BOOT_NAND_DEFCONFIG = mx6ul_var_dart_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-6UL_BUILD_RESULTS_STRETCH_V3_PLUS
• DEBIAN_BOOT_BOARD_SECTION = DART-6UL_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-6UL_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-6UL_SD_TREE_STRETCH_V3_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR6UL
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

VAR-SOM-MX7

stretch-4.9.11-mx7-v1.0

• RELEASE_NAME = stretch-4.9.11-mx7-v1.0
• RELEASE_LINK = RELEASE_STRETCH_V1.0_VAR-SOM-MX7
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.9.11-mx7-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX7/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTHNiQATuLGEsjNKtjysSOV0eyi9UznbvtR-32fJjIeMUbfN0HA-O5v3v6n66_gbWZhL-fVS5dZG4Eq/pubhtml
• MACHINE_NAME = var-som-mx7
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.11_1.0.0_ga-var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx7dvar_som_defconfig
• U-BOOT_NAND_DEFCONFIG = mx7dvar_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.imx-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.imx-nand
• SPL_SD_IMAGE_NAME = N/A
• SPL_NAND_IMAGE_NAME = N/A
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx7_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX7_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX7_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX7_DTB
• SD_TREE_SECTION = VAR-SOM-MX7_SD_TREE
• DEBIAN_FLASH_SD_FROM_GUI_SECTION = VAR-SOM-MX7_FLASH_SD_FROM_GUI
• READ_ONLY_ROOTFS = '
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX7
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_CONFIG_FILE = include/configs/mx7dvar_som.h
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0x600000
• DTB_START_ADDRESS = 0xde0000

stretch-4.9.88-mx7-v2.0

• RELEASE_NAME = stretch-4.9.88-mx7-v2.0
• RELEASE_LINK = RELEASE_STRETCH_V2.0_VAR-SOM-MX7
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.3
• RECOVERY_SD_NAME = stretch-4.9.88-mx7-v2.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX7/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTHNiQATuLGEsjNKtjysSOV0eyi9UznbvtR-32fJjIeMUbfN0HA-O5v3v6n66_gbWZhL-fVS5dZG4Eq/pubhtml
• MACHINE_NAME = var-som-mx7
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.9.88_2.0.0_ga-var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2017.03_4.9.11_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx7dvar_som_defconfig
• U-BOOT_NAND_DEFCONFIG = mx7dvar_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx7_var02
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX7_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX7_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX7_DTB
• SD_TREE_SECTION = VAR-SOM-MX7_SD_TREE
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX7
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_CONFIG_FILE = include/configs/mx7dvar_som.h
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0x600000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx7-v1.0

• RELEASE_NAME = buster-4.14.78-mx7-v1.0
• RELEASE_LINK = RELEASE_BUSTER_V1.0_VAR-SOM-MX7
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = buster-4.14.78-mx7-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX7/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vSJF0C67RbXdMSmTkr7-7j3muLn9IJlyvXkw3hgZCSJMfNPo4qDDDogb1ppKxqyuIV5irlT-rqIsIY1/pubhtml
• MACHINE_NAME = var-som-mx7
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx7dvar_som_defconfig
• U-BOOT_NAND_DEFCONFIG = mx7dvar_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX7_BUSTER_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX7_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX7_DTB
• SD_TREE_SECTION = VAR-SOM-MX7_SD_TREE
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX7
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_CONFIG_FILE = include/configs/mx7dvar_som.h
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0x600000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx7-v1.1

• RELEASE_NAME = buster-4.14.78-mx7-v1.1
• RELEASE_LINK = RELEASE_BUSTER_V1.1_VAR-SOM-MX7
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = buster-4.14.78-mx7-v1.1.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX7/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vSJF0C67RbXdMSmTkr7-7j3muLn9IJlyvXkw3hgZCSJMfNPo4qDDDogb1ppKxqyuIV5irlT-rqIsIY1/pubhtml
• MACHINE_NAME = var-som-mx7
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx_v7_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = mx7dvar_som_defconfig
• U-BOOT_NAND_DEFCONFIG = mx7dvar_som_nand_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• U-BOOT_NAND_IMAGE_NAME = u-boot.img-nand
• SPL_SD_IMAGE_NAME = SPL-sd
• SPL_NAND_IMAGE_NAME = SPL-nand
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX7_BUSTER_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX7_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX7_DTB
• SD_TREE_SECTION = VAR-SOM-MX7_SD_TREE
• EMMC_FAT_PARTITION_NAME = BOOT-VARMX7
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p2
• NAND_ROOTFS_DEV = mtd4
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_CONFIG_FILE = include/configs/mx7dvar_som.h
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0x600000
• DTB_START_ADDRESS = 0xde0000

DART-MX8M

stretch-4.14.78-mx8m-v1.0

• RELEASE_NAME = stretch-4.14.78-mx8m-v1.0
• RELEASE_LINK = RELEASE_STRETCH_V1.0_DART-MX8M
• DEBIAN_NAME = Stretch
• DEBIAN_VERSION = 9.8
• RECOVERY_SD_NAME = stretch-4.14.78-mx8m-v1.0.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTUPjdt-nbNyWUFxjrkoIw4H-s1h5Uo3HYgYQvzHgL1SMIutt7fzGm1zq5vgwLQhNAb7fTqETSjBn2J/pubhtml
• MACHINE_NAME = imx8m-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8m_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_stretch_mx8m_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-MX8M_SD_TREE_STRETCH_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx8m-v2.0

• RELEASE_NAME = buster-4.14.78-mx8m-v2.0
• RELEASE_LINK = RELEASE_BUSTER_V2.0_DART-MX8M
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mq-dart-debian-recovery-sd.v20.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/u/1/d/e/2PACX-1vQfCAlTXVzRnM40_E8FyDuW4xUQgL8fXjIqhf_61G9qHeZkpt4Qft0FDUvh5f6r20GjAxPGNY29XRxS/pubhtml
• MACHINE_NAME = imx8m-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8m_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M_BUSTER_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-MX8M_SD_TREE_STRETCH_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx8m-v2.1

• RELEASE_NAME = buster-4.14.78-mx8m-v2.1
• RELEASE_LINK = RELEASE_BUSTER_V2.1_DART-MX8M
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mq-dart-debian-recovery-sd.v21.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vSlrFOHAlD1kMZoSaju8jSjFfSGprzvHajAW7YH7_OP-DVgo68HYVaFjkJAltwOGDMTAS45ELPJl8Cl/pubhtml
• MACHINE_NAME = imx8m-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8m_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M_BUSTER_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-MX8M_SD_TREE_STRETCH_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx8m-v2.2

• RELEASE_NAME = buster-4.14.78-mx8m-v2.2
• RELEASE_LINK = RELEASE_BUSTER_V2.2_DART-MX8M
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mq-dart-debian-recovery-sd.v22.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vR_DwLA6MYlqqX791TixhrFoQWGKDRP9Au35jIHWiecJR7AxQtCINNAb0h7KqdGmfAIgSwU8N9NcK7f/pubhtml
• MACHINE_NAME = imx8m-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8m_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M_BUSTER_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M_DTB_STRETCH_PLUS
• SD_TREE_SECTION = DART-MX8M_SD_TREE_STRETCH_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk1
• EMMC_ROOTFS_PARTITION_NUM = p2
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

DART-MX8M-MINI

buster-4.14.78-mx8mm-v1.0

• RELEASE_NAME = buster-4.14.78-mx8mm-v1.0
• RELEASE_LINK = RELEASE_BUSTER_V1.0_DART-MX8M-MINI
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mm-dart-debian-recovery-sd.v10.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M-MINI/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vRSuSjOYHfWyX_zVbD3Srs7e2FqAh2UE5_E0UzbzASlzhWYWq5jxwNXxu6tKaGWCAD4BTZjRS9oxtQx/pubhtml
• MACHINE_NAME = imx8mm-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8mm_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M-MINI_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M-MINI_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M-MINI_DTB_BUSTER_PLUS
• SD_TREE_SECTION = DART-MX8M-MINI_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx8mm-v1.1

• RELEASE_NAME = buster-4.14.78-mx8mm-v1.1
• RELEASE_LINK = RELEASE_BUSTER_V1.1_DART-MX8M-MINI
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mm-dart-debian-recovery-sd.v11.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M-MINI/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vTlFMGOujEDFCx4hlDVZYhKNTbJt_TejMM3QPrjVLFzMe1B4ZKqY0Xq_U_VWCpUr4k0KBOUlMrzcKuH/pubhtml
• MACHINE_NAME = imx8mm-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8mm_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M-MINI_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M-MINI_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M-MINI_DTB_BUSTER_PLUS
• SD_TREE_SECTION = DART-MX8M-MINI_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.78-mx8mm-v1.2

• RELEASE_NAME = buster-4.14.78-mx8mm-v1.2
• RELEASE_LINK = RELEASE_BUSTER_V1.2_DART-MX8M-MINI
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8mm-dart-debian-recovery-sd.v12.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/DART-MX8M-MINI/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vRcyUJfq8ShqxORtbmXHTLr7cAu5pcceFeH9YBpqGK3rCYLph015vpuQ3zO6_lW__Gr0l8YbFLrLaIh/pubhtml
• MACHINE_NAME = imx8mm-var-dart
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.78_1.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.78_1.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8mm_var_dart_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = DART-MX8M-MINI_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = DART-MX8M-MINI_BOOT_BOARD
• KERNEL_DTB_SECTION = DART-MX8M-MINI_DTB_BUSTER_PLUS
• SD_TREE_SECTION = DART-MX8M-MINI_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk2
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

VAR-SOM-MX8X

buster-4.14.98-imx8qxp-v1.0

• RELEASE_NAME = buster-4.14.98-imx8qxp-v1.0
• RELEASE_LINK = RELEASE_BUSTER_V1.0_VAR-SOM-MX8X
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8qxp-var-som-debian-recovery-sd.v10.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vSFdtYHeAOWEEsQ-MdUNaCPKXTAo-bcuqc6McnzjukSyV1FfBKd7AgChVKIdfm_2Y4H8VqX5PuFmCyB/pubhtml
• MACHINE_NAME = imx8qxp-var-som
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.98_2.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.98_2.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8qxp_var_som_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX8X_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX8X_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX8X_DTB_BUSTER_PLUS
• SD_TREE_SECTION = VAR-SOM-MX8X_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.98-imx8qxp-v1.1

• RELEASE_NAME = buster-4.14.98-imx8qxp-v1.1
• RELEASE_LINK = RELEASE_BUSTER_V1.1_VAR-SOM-MX8X
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8qxp-var-som-debian-recovery-sd.v11.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vT5RERy_FKg71w2AXzSsuUrNYlSWgtY3fqtED29vXDSWBvlfLErL8lPhmgHR3UrXJ5yR3mryuVMyQw-/pubhtml
• MACHINE_NAME = imx8qxp-var-som
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.98_2.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.98_2.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8qxp_var_som_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX8X_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX8X_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX8X_DTB_BUSTER_PLUS
• SD_TREE_SECTION = VAR-SOM-MX8X_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

buster-4.14.98-imx8qxp-v1.2

• RELEASE_NAME = buster-4.14.98-imx8qxp-v1.2
• RELEASE_LINK = RELEASE_BUSTER_V1.2_VAR-SOM-MX8X
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = mx8qxp-var-som-debian-recovery-sd.v12.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vRyRN9mfqvHTvFSjnDO-NUnXU8KquqlAlZBm9iSWvRii3HBRQHB3_vuegtLAltIOS6ETTdvg74qUDLU/pubhtml
• MACHINE_NAME = imx8qxp-var-som
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.98_2.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.98_2.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8qxp_var_som_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX8X_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX8X_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX8X_DTB_BUSTER_PLUS
• SD_TREE_SECTION = VAR-SOM-MX8X_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000

VAR-SOM-MX8

buster-4.14.98-var-som-imx8-v1.0

• RELEASE_NAME = buster-4.14.98-var-som-imx8-v1.0
• RELEASE_LINK = RELEASE_BUSTER_V1.0_VAR-SOM-MX8
• DEBIAN_NAME = Buster
• DEBIAN_VERSION = 10
• RECOVERY_SD_NAME = var-som-mx8-debian-recovery-sd.v10.img.gz
• RECOVERY_SD_URL = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8/Software/debian
• RELEASE_NOTES_LINK = https://docs.google.com/spreadsheets/d/e/2PACX-1vQSP4zYfs8FtvCs-wUxW0pm-un17gvEWB1J6pM0y58zODPGRudTWzSteCT83npcbZgfcKmuvPjtFhOS/pubhtml
• MACHINE_NAME = imx8qm-var-som
• KERNEL_GIT = https://github.com/varigit/linux-imx.git
• KERNEL_BRANCH = imx_4.14.98_2.0.0_ga_var01
• KERNEL_IMAGE = zImage
• KERNEL_DEFCONFIG = imx8_var_defconfig
• U-BOOT_GIT = https://github.com/varigit/uboot-imx.git
• U-BOOT_BRANCH = imx_v2018.03_4.14.98_2.0.0_ga_var01
• U-BOOT_SD_DEFCONFIG = imx8qm_var_som_defconfig
• U-BOOT_SD_IMAGE_NAME = u-boot.img-sd
• DEBIAN_GIT = https://github.com/varigit/debian-var.git
• DEBIAN_BRANCH = debian_buster_var01
• DEBIAN_BUILD_RESULTS_SECTION = VAR-SOM-MX8_BUILD_RESULTS
• DEBIAN_BOOT_BOARD_SECTION = VAR-SOM-MX8_BOOT_BOARD
• KERNEL_DTB_SECTION = VAR-SOM-MX8_DTB_BUSTER_PLUS
• SD_TREE_SECTION = VAR-SOM-MX8_SD_TREE_BUSTER_PLUS
• EMMC_FAT_PARTITION_NAME = BOOT-VAR8M
• EMMC_ROOTFS_DEV = mmcblk0
• EMMC_ROOTFS_PARTITION_NUM = p1
• RAM_LOAD_ADDRESS = 0x83100000
• UBOOT_PAD_SIZE = 0x200000
• KERNEL_PAD_SIZE = 0x7e0000
• KERNEL_START_ADDRESS = 0xde0000
• DTB_START_ADDRESS = 0xde0000