VAR-SOM-MX6 DART eMMC flashing Jethro
Introduction
Variscite DART-MX6 SOM uses eMMC to boot.
This Wiki is only valid for DART-MX6
Yocto Build results
The resulted images are located at tmp/deploy/images/var-som-mx6.
Looking at tmp/deploy/images/var-som-mx6 you will find the following five required files for a complete system:
SPL, U-Boot, uImage, dtb file, file system image file.
| Image Name |
How to use | |||
|---|---|---|---|---|
| fsl-image-gui-var-som-mx6.tar.bz2 | Tarball of the rootfs | |||
| uImage | Linux kernel image | |||
| SPL-sd | SPL for SD/eMMC | |||
| u-boot-sd-2015.04-r0.img | U-Boot for SD/eMMC | |||
| Device Tree Name |
SOM type |
Carrier Board type |
LCD Type |
Evaluation Kit name |
| uImage-imx6q-var-dart.dtb | VAR-SOM-SOLO / VAR-SOM-DUAL | VAR-DT6CustomBoard | Capacitive LVDS touch | VAR-DVK-DT6 VAR-STK-DT6 |
eMMC Flashing scripts
If you followed the Create an extended SD card steps, the eMMC flashing scripts will be included in your SD card.
The eMMC flashing scripts are easy-to-use example scripts for burning images into eMMC.
eMMC images locations
Following is the directory structure on your SD card, which elaborates the files' location that the below flashing scripts are expecting:
/opt/images/
└── Yocto
├── SPL.mmc
├── rootfs.tar.bz2
├── u-boot.img.mmc
├── uImage
└── uImage-imx6q-var-dart.dtb
Prepare images for NAND flash / eMMC flashing
Plug the bootable SD card into your host machine.
Then your host machine should mount the rootfs partition on /media/rootfs.
Copy all the mentioned yocto-built binaries to the SD card:
- Note: If you followed the Create an extended SD card steps, the eMMC flashing scripts and all relevant binaries are already included in your SD card, and the below commands are redundant!
$ export YOCTO_IMGS_PATH=~/var-som-mx6-yocto-jethro/tmp/deploy/images/var-som-mx6
$ export P2_MOUNT_DIR=/media/rootfs/
Linux:
$ sudo cp ${YOCTO_IMGS_PATH}/uImage ${P2_MOUNT_DIR}/opt/images/Yocto/
SPL/U-Boot:
$ sudo cp ${YOCTO_IMGS_PATH}/SPL-sd ${P2_MOUNT_DIR}/opt/images/Yocto/SPL.mmc
$ sudo cp ${YOCTO_IMGS_PATH}/u-boot-sd-2015.04-r0.img ${P2_MOUNT_DIR}/opt/images/Yocto/u-boot.img.mmc
File System:
$ sudo cp ${YOCTO_IMGS_PATH}/fsl-image-gui-var-som-mx6.tar.bz2 ${P2_MOUNT_DIR}/opt/images/Yocto/rootfs.tar.bz2
Device Tree:
$ sudo cp ${YOCTO_IMGS_PATH}/uImage-imx6q-var-dart.dtb ${P2_MOUNT_DIR}/opt/images/Yocto/
eMMC flashing scripts
The flashing scripts are located on the SD card at /usr/bin/:
install_yocto.sh - Flash Yocto into NAND flash or eMMC (Run and follow usage instructions to install Yocto to DART eMMC) (install_yocto_emmc.sh - This script is being called by install_yocto.sh - it should not be called directly!)
Manual step-by-step flashing to eMMC
Flashing eMMC requires several steps including flashing of U-Boot and the Linux kernel, partition, format and untar of the file system.
We recommend to use our provided scripts to perform this task.
$ export node=/dev/mmcblk2 $ cd /opt/images/Yocto
Make sure the eMMC is not mounted:
$ umount ${node}p*
Delete current data on eMMC:
$ dd if=/dev/zero of=${node}p1 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p2 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p3 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p4 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p5 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p6 bs=1024 count=1024
$ dd if=/dev/zero of=${node}p7 bs=1024 count=1024
$ sync
$ (echo d; echo 1; echo d; echo 2; echo d; echo 3; echo d; echo w) | fdisk $node
$ sync
$ dd if=/dev/zero of=$node bs=1M count=4
$ sync
Create partition table:
$ (echo n; echo p; echo 1; echo 8192; echo 24575; echo t; echo c; \ echo n; echo p; echo 2; echo 24576; echo; \ echo p; echo w) | fdisk -u $node $ sync
Format the partitions:
$ mkfs.vfat ${node}p1 -n BOOT-VARSOM
$ mkfs.ext4 ${node}p2 -L rootfs
$ sync
Flash SPL and U-Boot
$ sudo dd if=SPL.mmc of=${node} bs=1K seek=1; sync
$ sudo dd if=u-boot.img.mmc of=${node} bs=1K seek=69; sync
Flash the Linux kernel to the BOOT partition
$ mkdir /run/media/mmcblk2p1
$ mount -t vfat ${node}p1 /run/media/mmcblk2p1
$ cp uImage-imx6q-var-dart.dtb /run/media/mmcblk2p1/imx6q-var-dart.dtb
$ cp uImage /run/media/mmcblk2p1/uImage
$ sync
$ umount /tmp/media/mmcblk2p1
Flash the rootfs:
$ mkdir /run/media/mmcblk2p1
$ mount ${node}p2 /run/media/mmcblk2p2
$ tar xvpf rootfs.tar.bz2 -C /run/media/mmcblk2p2
$ sync
$ umount /run/media/mmcblk2p2
Summary
This page is only valid for DART-MX6.
We described the results of a Yocto build, how to copy it to a bootable SD card and how to flash it to eMMC.
With our extended SD card and our recovery SD card we provide an installation script located at /usr/bin/install_yocto.sh. It is much safer to use it instead of flashing the system manually.