VAR-SOM-MX6 Android Unit Testing KK 100
Audio
The default Android sound recorder application use a a very low sampling rate producing a poor sound.
Plug a Disk-On-Key FAT32 formated into the USB host port.
Plug an audio source (like a PC line out or smartphone line out) into the line in connector.
Plug speakers (like PC speakers) into the line out connector.
root@android:/ # tinycap /mnt/media_rw/extsd/test0.wav
Hit CTRL-C after couple of seconds or more.
root@android:/ # tinyplay /mnt/media_rw/extsd/test0.wav
USB OTG as a device
Test the OTG as a device using Android ADB tool.
On target:
Under devloper option enable ADB debugguing
On Host:
$ sudo out/host/linux-x86/bin/adb kill-server $ sudo out/host/linux-x86/bin/adb start-server $ sudo out/host/linux-x86/bin/adb devices $ sudo out/host/linux-x86/bin/adb shell
USB OTG as a host
Use an external HUB. Plug into it a Disk-On-Key, mouse and keyboard.
Make sure with the Android GUI that they are functional. Test USB Stick with:
$ dd if=/dev/zero of=/dev/sdb bs=128K count=10000
USB HOST
Plug a mouse into all 3 ports and make sure it is working.
Use an external HUB. Plug into it a Disk-On-Key, mouse and keyboard.
Plug it into all 3 ports and make sure all 3 devices are functioning.
FASTBOOT
Install tools on host:
$ sudo add-apt-repository ppa:nilarimogard/webupd8 $ sudo apt-get update $ sudo apt-get android-tools-fastboot $ sudo apt-get install android-tools-adb android-tools-fastboot
Boot the target press spacebar to stop at u-boot and run "fastboot".
From KitKat build folder
$ sudo `which fastboot` flash boot out/target/product/var_som_mx6/boot.img $ sudo `which fastboot` flash recovery out/target/product/var_som_mx6/recovery.img $ sudo `which fastboot` flash android_root out/target/product/var_som_mx6/android_root.img $ sudo `which fastboot` reboot
HDMI
Boot the system and press spacebar to get into u-boot.
Change enviroment setting with the folowing command
setenv bootargs console=ttymxc0,115200 init=/init video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=32 video=mxcfb2:off vmalloc=400M androidboot.console=ttymxc0 androidboot.hardware=freescale caam mtdparts=gpmi-nand:4m(bootloader),16m(bootimg),28m(recovery),-(root) ubi.mtd=3 var_ts_type=ctw6120 mxc_hdmi.only_cea=1
Plug an HDMI TV or monitor to the HDMI port and boot the system by typing boot into u-boot.
You should see the Android on a full 1080p device.
Audio over HDMI
Download and install SoundAbout pm install /mnt/media_rw/udisk/apk/SoundAbout-com.woodslink.android.wiredheadphoneroutingfix-122-v2.5.8.0.apk Use the GUI to set the service as foreground and select the audio over HDMI.
External LVDS display
Boot the system and press spacebar to get into u-boot.
Change enviroment setting with the folowing command
For Quad, Dual and DualLite SOM's use:
setenv bootargs console=ttymxc0,115200 init=/init ldb=sin1 video=mxcfb0:dev=ldb,800x600M@60,bpp=32 video=mxcfb2:off vmalloc=400M androidboot.console=ttymxc0 androidboot.hardware=freescale caam mtdparts=gpmi-nand:4m(bootloader),16m(bootimg),28m(recovery),-(root) ubi.mtd=3 androidboot.serialno=190e61d4df64632c var_ts_type=ctw6120
Ethernet
Just plug a cable into the system
WLAN
Setup
VAR-SOM-MX6 V2.X & V1.x(Wilink6/WiLink8): First time need to set mac address to be used automatically
$ mount -o remount,rw /system $ calibrator set nvs_mac /system/etc/firmware/ti-connectivity/wl1271-nvs.bin 00:00:00:00:00:00
VAR-SOM-MX6 V2.X (WiLink8): First time need to select your correct device
- Select your WL183x p/n:
$ mount -o remount,rw /system $ cd /etc/wifi/wlconf $ . ./configure-device.sh wl1831 select one out of : WL1831, WL1833, WL1835, WL1837. As a result some additional information may be required like 1/2 antenna connected
Test
Use the Android GUI to enable and connect to a WIFI AP.
BLUETOOTH
Use the Android GUI to enable.
Test with file transfer to host PC, Bluetooth mouse and Bluetooth keyboard.
Camera
Use the Android GUI to activate and test the camera. You can take a picture and send it over Bluetooth to a PC host.
First time boot of Android must be with camera module installed. If you booted without the camera module installed Android will mark the system as "no camera". In such a case you need to re flash the Android and first time boot it with camera installed.
SATA
cat /proc/scsi/scsi busybox fdisk -ul /dev/block/sda
In the above commands you will see SCSI status and device partition table.
If the device is FAT32 formated Android will auto mount it.
RTC (Real Time Clock)
Disable the auto clock sync from the Android GUI.
busybox date 2013.12.01-10:50 busybox hwclock --systohc
Also can set clock via GUI and check it later.
In any method power down the board and wait 5 minutes. After that power up the board and check the the clock is correct.
Canbus
We added support for canbus in the kernel and the support library layer.
Connect 2 boards. Each board JP26 connect to the other with the right cable. Set the 2 boards:
$ ip link set can0 up type can bitrate 1000000 $ busybox ifconfig can0 up up
On board 1:
$ candump can0
On board 2:
$ cansend can0 500#1E.10.10