DART-6UL/VAR-SOM-MX7 Wireless LAN: Difference between revisions
(Created page with "{{PageHeader|DART-6UL - Wireless LAN}} {{DocImage|category1=DART-6UL|category2=Yocto}} __toc__ = Test = '''Scan for wireless networks''': <pre> $ ifconfig wlan0 up $ iw dev w...") |
No edit summary |
||
| Line 67: | Line 67: | ||
</pre> | </pre> | ||
Reinstall the driver is AP mode. | Reinstall the driver is AP mode. | ||
< | Wireless configuration can be setup in file /etc/hostapd.conf before launching hostapd<br> | ||
For configuring password access point name etc. | |||
for example: | |||
ssid=DART6UL_AP | |||
wpa_passphrase=12345678 | |||
IP Forwarding: | IP Forwarding: | ||
| Line 85: | Line 80: | ||
$ iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE | $ iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE | ||
</pre> | </pre> | ||
As a next step one should take a look at / | |||
As a next step one should take a look at iw utility which can be used for tuning some parameters https://wireless.wiki.kernel.org/en/users/documentation/iw | |||
Revision as of 08:39, 16 August 2016
Test
Scan for wireless networks:
$ ifconfig wlan0 up $ iw dev wlan0 scan | grep SSID
Connecting to a WPA encrypted network:
Find your network from the above scan command.
$ mv /etc/wpa_supplicant.conf /etc/wpa_supplicant.conf.org $ wpa_passphrase <YourAP> <YourPassword> >/etc/wpa_supplicant.conf $ wpa_supplicant -B -Dnl80211 -iwlan0 -c/etc/wpa_supplicant.conf
wait for:
wl_bss_connect_done succeeded with 88:5a:92:1d:7c:20
Check link:
$ iw dev wlan0 link
Disable eth0:
$ ifconfig eth0 down $ ifconfig eth1 down
Run DHCP:
$ udhcpc -iwlan0 $ ifconfig
Check link speed On server:
$ iperf -s
On target:
$ iperf -c 192.168.0.103
Useful link for common iw commands: https://wiki.archlinux.org/index.php/Wireless_network_configuration#Manual_setup
Access Point
This example will demonstrate you how to use the DART-6UL as an access point. It will forward packets from wlan0 to eth0. DHCPD:
$ vi /etc/udhcpd.conf # Sample udhcpd configuration file (/etc/udhcpd.conf) # The start and end of the IP lease block start 192.168.5.20 #default: 192.168.0.20 end 192.168.5.25 #default: 192.168.0.254 # The interface that udhcpd will use interface wlan0 #default: eth0 #Example opt dns 8.8.8.8 8.8.4.4 # public google dns servers option subnet 255.255.255.0 opt router 192.168.5.1 option lease 864000 # 10 days of seconds
This is a network example. You need to set the IP address based on your network.
First ensure that wpa_supplicant is not holding the device
$ killall wpa_supplicant $ killall hostapd
Reinstall the driver is AP mode.
Wireless configuration can be setup in file /etc/hostapd.conf before launching hostapd
For configuring password access point name etc.
for example:
ssid=DART6UL_AP
wpa_passphrase=12345678
IP Forwarding:
$ echo 1 > /proc/sys/net/ipv4/ip_forward $ ifconfig wlan0 192.168.5.1 $ hostapd -B /etc/hostapd.conf -P /var/run/hostapd.pid $ udhcpd /etc/udhcpd.conf $ iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
As a next step one should take a look at iw utility which can be used for tuning some parameters https://wireless.wiki.kernel.org/en/users/documentation/iw