MCUXpresso Platform Customization: Difference between revisions

From Variscite Wiki
Line 3,582: Line 3,582:
=== Running a demo ===
=== Running a demo ===


== Running a demo from U-Boot ==
=== Running a demo from U-Boot ===


To assist in loading {{#var:CORTEX_M_TYPE}} firmware from U-Boot prior to Linux boot, Variscite has created a dedicated set of U-Boot environment commands to assist in this.  
To assist in loading {{#var:CORTEX_M_TYPE}} firmware from U-Boot prior to Linux boot, Variscite has created a dedicated set of U-Boot environment commands to assist in this.  

Revision as of 20:52, 2 August 2023


DART-MX8M

Sections

Available dtbs

To allow Cortex M4 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, by selecting the right version with the symbolic link in the /boot folder of the booting media.
These device trees contain m4 label in their name.


The below table lists an example dtb blob file name for DART-MX8M (on DT8MCustomBoard rev. 1.3 and higher) with support for M4 (and SD card and LVDS), for each kernel version / Yocto release:

File Name
 Description
imx8mq-var-dart-dt8mcustomboard-m4-sd-lvds.dtb For kernel >= 5.4.85 (Yocto >= Dunfell)
imx8mq-var-dart-m4-sd-lvds.dtb For kernel = 5.4.24 (Yocto Zeus)
fsl-imx8mq-var-dart-m4-sd-lvds.dtb For kernel = 4.19.35 (Yocto Warrior)
Image.gz-fsl-imx8mq-var-dart-m4-sd-lvds.dtb For kernel = 4.14.98 (Yocto Sumo)

For the full list of device tree blob files, refer to the "Build Results" section in the appropriate wiki page for the specific Yocto/Debian release you are using.

Default M4 pins

Default M4 pins used by the demos are:

Function Pin
debug UART (UART2) RX: J12.6 / TX: J12.4
GPIO (GPIO4_IO03) LED7 for DT8CustomBoard 1.x
U43.2 / R228 for DT8CustomBoard >= 2.0 (Use Oscilloscope to observe output signal)
I2C (I2C3) SCL: J12.18 / SDA: J12.20
PWM (PWM2) J14.3

Available Demos

  • driver_examples/i2c/interrupt_b2b_transfer/slave
  • driver_examples/i2c/interrupt_b2b_transfer/master
  • driver_examples/i2c/polling_b2b_transfer/slave
  • driver_examples/i2c/polling_b2b_transfer/master
  • driver_examples/wdog
  • driver_examples/gpio/led_output
  • driver_examples/tmu/tmu_monitor_report
  • driver_examples/pwm
  • driver_examples/uart/auto_baudrate_detect
  • driver_examples/uart/interrupt
  • driver_examples/uart/interrupt_rb_transfer
  • driver_examples/uart/polling
  • driver_examples/uart/interrupt_transfer
  • driver_examples/gpt/timer
  • driver_examples/gpt/capture
  • driver_examples/ecspi/ecspi_loopback
  • driver_examples/qspi/polling_transfer
  • driver_examples/rdc
  • driver_examples/sema4/uboot
  • rtos_examples/freertos_ecspi/ecspi_loopback
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_uart
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer
  • rtos_examples/freertos_i2c
  • cmsis_driver_examples/i2c/int_b2b_transfer/slave
  • cmsis_driver_examples/i2c/int_b2b_transfer/master
  • cmsis_driver_examples/uart/interrupt_transfer
  • cmsis_driver_examples/ecspi/int_loopback_transfer
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • demo_apps/hello_world

NXP Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M4 as described in related linker file.

memory type M4 memory area A53 memory area memory lentgh linker file
DDR 0x80000000-0x801FFFFF (code)
0x80200000-0x803FFFFF (data)
0x80400000-0x80FFFFFF (data2) 		0x80000000-0x801FFFFF (code)
0x80200000-0x803FFFFF (data)
0x80400000-0x80FFFFFF (data2) 		16MB (DDR) MIMX8MQ6xxxJZ_cm4_ddr_ram.ld
TCM 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x80000000-0x80FFFFFF (data2) 		0x007E0000-0x007FFFFF (code)
0x00800000-0x0081FFFF (data)
0x80000000-0x80FFFFFF (data2) 		256kB (TCM) + 16MB (DDR) MIMX8MQ6xxxJZ_cm4_ram.ld

All linker files are locate in the armgcc folder of each demo.

The DDR reserved area must match the one declared in the kernel device tree: at least 2 GB of RAM is required on the SoM to allow Cortex-M4 accessing the range 0x80000000 - 0x80FFFFFF.

The RPMSG area is located at 0xB8000000: at least 3 GB of RAM is required on the SoM to allow Cortex-M4 accessing the RPMSG area. After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8M Applications Processor Reference Manual paragraphs:

  • 2.1.2 Cortex-A53 Memory Map
  • 2.1.3 Cortex-M4 Memory Map

Variscite Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M4 as described in related linker file.

memory type M4 memory area A53 memory area memory lentgh linker file
DDR 0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		16MB (DDR) MIMX8MQ6xxxJZ_cm4_ddr_ram.ld
TCM 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		0x007E0000-0x007FFFFF (code)
0x00800000-0x0081FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		256kB (TCM) + 16MB (DDR) MIMX8MQ6xxxJZ_cm4_ram.ld

All linker files are locate in the armgcc folder of each demo.

The DDR reserved area must match the one declared in the kernel device tree: at least 1 GB of RAM is required on the SoM to allow Cortex-M4 accessing the range 0x7E000000 - 0x7EFFFFFF. For some reason, Cortex-M4 is not able to access RAM locations below 0x60000000: SoMs with 512 MB of RAM are not suitable to use Cortex-M4.

The RPMSG area is located at 0x40000000: all SoMs allow Cortex-M4 accessing the RPMSG area.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8M Applications Processor Reference Manual paragraphs:

  • 2.1.2 Cortex-A53 Memory Map
  • 2.1.3 Cortex-M4 Memory Map

JTAG

The VAR-DT8MCustomBoard exports the DART-MX8M JTAG signals through J29, a standard 1.27" 10 pin header.

Here is the pinout:

pin signal description pin signal description
1 JTAG_VREF JTAG IO reference voltage,
connects to SOM_NVCC_3V3. 		2 JTAG_TMS JTAG Mode Select signal
3 GND Digital Ground 4 JTAG_TCK JTAG Clock signal,
requires 10K pull down.
5 GND Digital Ground 6 JTAG_TDO JTAG Data Out signal
7 GND Digital Ground 8 JTAG_TDI JTAG Data In signal
9 JTAG_NTRST_C JTAG Reset signal 10 NRST_CON Programmer Reset,
used to put the SOC in reset state.

Please refer to board schematics for further details.

Releases

mcuxpresso-2.5.1-mx8mq-v1.0

  • HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.5.1-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.5.1_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.5.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.5.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/7-2018q2/gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-7-2018-q2-update
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_NXP_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK i.MX 8M Devices.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ

mcuxpresso-2.5.1-mx8mq-v1.1

   *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.5.1-mx8mq-v1.1
  • RELEASE_LINK = MCUXPRESSO_2.5.1_V1.1_DART-MX8M
  • MCUXPRESSO_VERSION = 2.5.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.5.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/7-2018q2/gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-7-2018-q2-update
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK i.MX 8M Devices.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ

mcuxpresso-2.8.0-mx8mq-v1.0

 *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.8.0-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.8.0_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.8.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.8.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MQ.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ

mcuxpresso-2.9.0-mx8mq-v1.0

 *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.9.0-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.9.0_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.9.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.9.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MQ.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mq-v1.0

mcuxpresso-2.10.0-mx8mq-v1.0

 *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.10.0-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.10.0_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.10.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.10.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10-2020q4/gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10-2020-q4-major
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MQ.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mq-v1.3
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8MQ-deactivated-the-LMEM-caches-to-debug-in-exter.patch
  • BOARD_SDK = dart_mx8mq

mcuxpresso-2.11.1-mx8mq-v1.0

 *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.11.1-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.11.1_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.11.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.11.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.07/gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.07
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MQ.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mq-v1.5
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8MQ-deactivated-the-LMEM-caches-to-debug-in-exter.patch
  • BOARD_SDK = dart_mx8mq

mcuxpresso-2.12.1-mx8mq-v1.0

 *HARDWARE_NAME = DART-MX8M
  • RELEASE_NAME = mcuxpresso-2.12.1-mx8mq-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.12.1_V1.0_DART-MX8M
  • MCUXPRESSO_VERSION = 2.12.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.12.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.10/gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.10
  • BOARD_FOLDER = boards/dart_mx8mq
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MQ.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MQ
  • YOCTO_RELEASE_TAG = mx8m-yocto-kirkstone-5.15-2.0.x-v1.0
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8MQ-deactivated-the-LMEM-caches-to-debug-in-exter.patch
  • BOARD_SDK = dart_mx8mq

mcuxpresso-2.13.0-mx8mq-v1.0


DART-MX8M-MINI

Sections

Available dtbs

To allow Cortex M4 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, containing m4 label in the name, using the fdt_file environment variable in U-Boot.

This device tree disables some of the base device tree nodes in order to avoid conflicts between the main processor and Cortex M4.

File Name
 Description
imx8mm-var-dart-dt8mcustomboard-m4.dtb DART-MX8M-MINI device tree blob for kernel >= 5.4.74 (Yocto Dunfell)
imx8mm-var-dart-m4.dtb DART-MX8M-MINI device tree blob for kernel 5.4.3 (Yocto Zeus) on SOM rev. > 1.0
fsl-imx8mm-var-dart-m4.dtb DART-MX8M-MINI device tree blob for in kernels < 5.4.3 on SOM rev. > 1.0
imx8mm-var-som-symphony-m4.dtb VAR-SOM-MX8M-MINI device tree blob for kernel >= 5.4.74 (Yocto Dunfell) on Symphony-Board 1.4a and above
imx8mm-var-som-symphony-legacy-m4.dtb VAR-SOM-MX8M-MINI device tree blob for kernel >= 5.4.74 (Yocto Dunfell) on Symphony-Board 1.4 and below
imx8mm-var-som-m4.dtb VAR-SOM-MX8M-MINI device tree blob for kernel 5.4.3 (Yocto Zeus) on SOM rev. > 1.0
imx8mm-var-som-rev10-m4.dtb VAR-SOM-MX8M-MINI device tree blob for kernel 5.4.3 (Yocto Zeus) on SOM rev. 1.0
fsl-imx8mm-var-som-m4.dtb VAR-SOM-MX8M-MINI device tree blob for in kernels < 5.4.3 on SOM rev. > 1.0
fsl-imx8mm-var-som-rev10-m4.dtb VAR-SOM-MX8M-MINI device tree blob for in kernels < 5.4.3 on SOM rev. 1.0


Default M4 pins

Default M4 pins used by the demos are:

Function Pin
Debug UART (UART2) RX: J12.6 / TX: J12.4
GPIO (GPIO4_IO03) LED7
I2C (I2C4) SCL: J12.17 / SDA: J12.19
PWM (PWM2) J14.3

Default M4 pins v2

Default M4 pins used by the demos are:

Function SoC balls DART-MX8M-MINI pins DT8MCB pins VAR-SOM-MX8M-MINI pins Symphony pins Notes
UART3 RX/TX E18 / D18 J2.87 / J2.89 J12.11 / J12.13 J1.175 / J1.124 J18.5 / J18.3
GPIO4_IO03 AF15 J2.59 GPLED1 J1.84 J17.3 The led_output demo makes the GPLED1 blink for only DT8MCustomBoard 1.x, use the scope on one of the following test points for DT8MCustomBoard >= 2.x (U43.2/R228/MIPI-CSI pin 20)
I2C4 SCL/SDA D13 / E13 J1.17 / J1.19 J12.17/ J12.19 J1.174 / J1.176 J16.10 / J16.12
PWM3 AF9 J3.36 J14.7 J1.69 J18.2
SPI1 CS0/SCK/SDI/SDO B6 / D6 / A7 / B7 J2.79 / J2.77 / J2.81 / J2.83 J16.4/ J16.2 / J16.8 / J16.6 J1.39 / J1.43 / J1.41 / J1.45 J16.4/ J16.2 / J16.6 / J16.8 Enabling it SPI devices will be no longer visible from Linux

Available Demos

  • driver_examples/i2c/interrupt_b2b_transfer/slave
  • driver_examples/i2c/interrupt_b2b_transfer/master
  • driver_examples/i2c/polling_b2b_transfer/slave
  • driver_examples/i2c/polling_b2b_transfer/master
  • driver_examples/wdog
  • driver_examples/sdma/scatter_gather
  • driver_examples/sdma/memory_to_memory
  • driver_examples/gpio/led_output
  • driver_examples/pwm
  • driver_examples/uart/auto_baudrate_detect
  • driver_examples/uart/interrupt
  • driver_examples/uart/idle_detect_sdma_transfer
  • driver_examples/uart/interrupt_rb_transfer
  • driver_examples/uart/sdma_transfer
  • driver_examples/uart/polling
  • driver_examples/uart/interrupt_transfer
  • driver_examples/gpt/timer
  • driver_examples/gpt/capture
  • driver_examples/ecspi/ecspi_loopback
  • driver_examples/ecspi/interrupt_b2b_transfer/slave
  • driver_examples/ecspi/interrupt_b2b_transfer/master
  • driver_examples/ecspi/polling_b2b_transfer/slave
  • driver_examples/ecspi/polling_b2b_transfer/master
  • driver_examples/rdc
  • driver_examples/tmu_1/monitor_threshold
  • driver_examples/tmu_1/temperature_polling
  • driver_examples/sema4/uboot
  • rtos_examples/freertos_ecspi/ecspi_loopback
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_uart
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer
  • rtos_examples/freertos_i2c
  • cmsis_driver_examples/i2c/int_b2b_transfer/slave
  • cmsis_driver_examples/i2c/int_b2b_transfer/master
  • cmsis_driver_examples/uart/sdma_transfer
  • cmsis_driver_examples/uart/interrupt_transfer
  • cmsis_driver_examples/ecspi/int_loopback_transfer
  • cmsis_driver_examples/ecspi/sdma_loopback_transfer
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • demo_apps/hello_world

Variscite Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M4 as described in related linker file.

memory type M4 memory area A53 memory area memory lentgh linker file
DDR 0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		16MB (DDR) MIMX8MM6xxxxx_cm4_ddr_ram.ld
TCM 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		0x007E0000-0x007FFFFF (code)
0x00800000-0x0081FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		256kB (TCM) + 16MB (DDR) MIMX8MM6xxxxx_cm4_ram.ld

All linker files are locate in the armgcc folder of each demo.

The DDR reserved area must match the one declared in the kernel device tree: at least 1 GB of RAM is required on the SoM to allow Cortex-M4 accessing the range 0x7E000000 - 0x7EFFFFFF. For some reason, Cortex-M4 is not able to access RAM locations below 0x60000000: SoMs with 512 MB of RAM are not suitable to use Cortex-M4.

The RPMSG area is located at 0x40000000: all SoMs allow Cortex-M4 accessing the RPMSG area.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8M Mini Applications Processor Reference Manual paragraphs:

  • 2.1.2 Cortex-A53 Memory Map
  • 2.1.3 Cortex-M4 Memory Map

Releases

freertos-1.0.1-mx7-v1.0


mcuxpresso-2.5.0-mx8mm-v1.0

  • HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.5.0-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.5.0_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.5.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.5.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/7-2018q2/gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-7-2018-q2-update
  • BOARD_FOLDER = boards/dart_mx8mm
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for i.MX 8M Mini.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM

mcuxpresso-2.5.0-mx8mm-v1.1

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.5.0-mx8mm-v1.1
  • RELEASE_LINK = MCUXPRESSO_2.5.0_V1.1_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.5.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.5.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/7-2018q2/gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-7-2018-q2-update
  • BOARD_FOLDER = boards/dart_mx8mm
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for i.MX 8M Mini.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM

mcuxpresso-2.8.0-mx8mm-v1.0

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.8.0-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.8.0_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.8.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.8.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/dart_mx8mm
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MM.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM

mcuxpresso-2.9.0-mx8mm-v1.0

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.9.0-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.9.0_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.9.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.9.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/dart_mx8mm
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MM.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mm-v1.1

mcuxpresso-2.10.0-mx8mm-v1.0

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.10.0-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.10.0_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.10.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.10.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10-2020q4/gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10-2020-q4-major
  • BOARD_FOLDER = boards/dart_mx8mm
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8M-MINI-deactivated-the-LMEM-caches-to-debug-in-e.patch
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MM.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM
  • YOCTO_RELEASE_TAG = hardknott-fslc-5.4-2.3.x-mx8mm-v1.1

mcuxpresso-2.11.1-mx8mm-v1.0

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.11.1-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.11.1_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.11.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.11.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.07/gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.07
  • BOARD_FOLDER = boards/dart_mx8mm
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8M-MINI-deactivated-the-LMEM-caches-to-debug-in-e.patch
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MM.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM
  • YOCTO_RELEASE_TAG = hardknott-fslc-5.4-2.3.x-mx8mm-v1.4

mcuxpresso-2.12.1-mx8mm-v1.0

   *HARDWARE_NAME = DART-MX8M-MINI
  • RELEASE_NAME = mcuxpresso-2.12.1-mx8mm-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.12.1_V1.0_DART-MX8M-MINI
  • MCUXPRESSO_VERSION = 2.12.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.12.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.10/gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.10
  • BOARD_FOLDER = boards/dart_mx8mm
  • DEACTIVATE_LMEM_CACHE_PATCH = 0001-iMX8M-MINI-deactivated-the-LMEM-caches-to-debug-in-e.patch
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-MINI_PINS_SECTION_V2
  • DEMOS_SECTION = DART-MX8M-MINI_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-MINI_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-MINI_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MM.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MM
  • YOCTO_RELEASE_TAG = mx8mm-yocto-kirkstone-5.15-2.0.x-v1.0

mcuxpresso-2.13.0-mx8mm-v1.0


VAR-SOM-MX8M-NANO

Sections

Available dtbs

To allow Cortex M7 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, containing m7 label in the name, using the fdt_file environment variable in U-Boot.

File Name
 Description
imx8mn-var-som-symphony-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel = 5.4.74 (Yocto Dunfell) on Symphony-Board 1.4a and above and for kernel >= 5.10.72 (Yocto Hardknott) on all Symphony-Boards
imx8mn-var-som-symphony-legacy-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel = 5.4.74 (Yocto Dunfell) on Symphony-Board 1.4 and below
imx8mn-var-som-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel 5.4.3 - 5.4.24 (Yocto Zeus) on som rev > 1.0
imx8mn-var-som-rev10-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel 5.4.3 - 5.4.24 (Yocto Zeus) on som rev 1.0
fsl-imx8mn-var-som-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel < 5.4.3 on som rev > 1.0
fsl-imx8mn-var-som-rev10-m7.dtb VAR-SOM-MX8M-NANO device tree blob for kernel < 5.4.3 on som rev 1.0

This device tree disables some of the base device tree nodes in order to avoid conflicts between the main processor and Cortex M7.

Default M7 pins

Default M7 pins used by the demos are:

Function SoC balls VAR-SOM-MX8M-NANO pins Symphony pins Notes
UART3 RX/TX E18 / D18 J1.175 / J1.124 J18.5 / J18.3
GPIO4_IO23 AC24 J1.21 J16.5
I2C4 SCL/SDA D13 / E13 J1.174 / J1.176 J16.10 / J16.12
PWM3 AF9 J1.69 J18.2
SPI1 CS0/SCK/SDI/SDO B6 / D6 / A7 / B7 J1.39 / J1.43 / J1.41 / J1.45 J16.4/ J16.2 / J16.6 / J16.8 Enabling it SPI devices will be no longer visible from Linux

Available Demos

  • driver_examples/i2c/interrupt_b2b_transfer/slave
  • driver_examples/i2c/interrupt_b2b_transfer/master
  • driver_examples/i2c/polling_b2b_transfer/slave
  • driver_examples/i2c/polling_b2b_transfer/master
  • driver_examples/wdog
  • driver_examples/sdma/scatter_gather
  • driver_examples/sdma/memory_to_memory
  • driver_examples/gpio/led_output
  • driver_examples/pwm
  • driver_examples/uart/auto_baudrate_detect
  • driver_examples/uart/interrupt
  • driver_examples/uart/idle_detect_sdma_transfer
  • driver_examples/uart/interrupt_rb_transfer
  • driver_examples/uart/sdma_transfer
  • driver_examples/uart/polling
  • driver_examples/uart/interrupt_transfer
  • driver_examples/gpt/timer
  • driver_examples/gpt/capture
  • driver_examples/ecspi/ecspi_loopback
  • driver_examples/ecspi/interrupt_b2b_transfer/slave
  • driver_examples/ecspi/interrupt_b2b_transfer/master
  • driver_examples/ecspi/polling_b2b_transfer/slave
  • driver_examples/ecspi/polling_b2b_transfer/master
  • driver_examples/rdc
  • driver_examples/tmu_1/monitor_threshold
  • driver_examples/tmu_1/temperature_polling
  • driver_examples/sema4/uboot
  • rtos_examples/freertos_ecspi/ecspi_loopback
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_uart
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer
  • rtos_examples/freertos_i2c
  • cmsis_driver_examples/i2c/int_b2b_transfer/slave
  • cmsis_driver_examples/i2c/int_b2b_transfer/master
  • cmsis_driver_examples/uart/sdma_transfer
  • cmsis_driver_examples/uart/interrupt_transfer
  • cmsis_driver_examples/ecspi/int_loopback_transfer
  • cmsis_driver_examples/ecspi/sdma_loopback_transfer
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • demo_apps/hello_world

Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M7 as described in related linker file.

memory type M7 memory area A53 memory area memory lentgh linker file
DDR 0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		0x7E000000-0x7E1FFFFF (code)
0x7E200000-0x7E3FFFFF (data)
0x7E400000-0x7EFFFFFF (data2) 		16MB (DDR) MIMX8MN6xxxxx_cm7_ddr_ram.ld
TCM 0x00000000-0x0001FFFF (code)
0x20000000-0x2001FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		0x007E0000-0x007FFFFF (code)
0x00800000-0x0081FFFF (data)
0x7E000000-0x7EFFFFFF (data2) 		256kB (TCM) + 16MB (DDR) MIMX8MN6xxxxx_cm7_ram.ld

All linker files are locate in the armgcc folder of each demo.

The DDR reserved area must match the one declared in the kernel device tree: at least 1 GB of RAM is required on the SoM to allow Cortex-M7 accessing the range 0x7E000000 - 0x7EFFFFFF. For some reason, Cortex-M7 is not able to access RAM locations below 0x60000000: SoMs with 512 MB of RAM are not suitable to use Cortex-M7.

The RPMSG area is located at 0x40000000: all SoMs allow Cortex-M7 accessing the RPMSG area.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8M Nano Applications Processor Reference Manual paragraphs:

  • 2.1.2 Cortex-A53 Memory Map
  • 2.1.3 Cortex-M7 Memory Map

JTAG

VAR-SOM-MX8M-NANO exposes JTAG signals on a header (not assembled by default) on the SOM top left side.

Here is the pinout:

pin signal description pin signal description
1 JTAG_VREF JTAG IO reference voltage,
connected to SOM_3V3_PER via 150 Ohm. 		2 JTAG_TMS JTAG Mode Select signal
3 GND Digital Ground 4 JTAG_TCK JTAG Clock signal,
include PD of 8.2K Ohm.
5 GND Digital Ground 6 JTAG_TDO JTAG Data Out signal
7 GND Digital Ground 8 JTAG_TDI JTAG Data In signal
9 JTAG_TRST_B JTAG Reset signal,
active low signal 		10 POR_B Programmer Reset,
used to put the SOC in reset state.

Please refer to SoM datasheet for further details.

Releases

mcuxpresso-2.7.0-mx8mn-v1.0

   *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.7.0-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.7.0_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.7.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.7.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/8-2019q3/RC1.1/gcc-arm-none-eabi-8-2019-q3-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-8-2019-q3-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-8-2019-q3-update
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN

mcuxpresso-2.8.0-mx8mn-v1.0

 *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.8.0-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.8.0_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.8.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.8.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN

mcuxpresso-2.9.0-mx8mn-v1.0

 *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.9.0-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.9.0_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.9.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.9.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mn-v1.1

mcuxpresso-2.10.0-mx8mn-v1.0

 *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.10.0-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.10.0_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.10.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.10.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10-2020q4/gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10-2020-q4-major
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mn-v1.6

mcuxpresso-2.11.1-mx8mn-v1.0

 *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.11.1-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.11.1_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.11.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.11.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.07/gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.07
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8mn-v1.8

mcuxpresso-2.12.1-mx8mn-v1.0

 *HARDWARE_NAME = VAR-SOM-MX8M-NANO
  • SOC_HAS_M7 = true
  • RELEASE_NAME = mcuxpresso-2.12.1-mx8mn-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.12.1_V1.0_VAR-SOM-MX8M-NANO
  • MCUXPRESSO_VERSION = 2.12.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.12.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.10/gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.10
  • BOARD_FOLDER = boards/som_mx8mn
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8M-NANO_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8M-NANO_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8M-NANO_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8MN_MEMORY-TYPES
  • JTAG_SECTION = VAR-SOM-MX8MN_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MN.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MN
  • YOCTO_RELEASE_TAG = mx8mn-yocto-hardknott-5.10.72_2.2.1-v1.0

mcuxpresso-2.13.0-mx8mn-v1.0


DART-MX8M-PLUS

Sections

Available dtbs

To allow Cortex M7 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, containing m7 label in the name, using the fdt_file environment variable in U-Boot.

This device tree disables some of the base device tree nodes in order to avoid conflicts between the main processor and Cortex M7.

File Name
 Description
imx8mp-var-dart-dt8customboard-m7.dtb DART-MX8M-PLUS device tree blob for kernel >= 5.4.70 (Yocto Zeus) on DT8MCustomBoard 2.x
imx8mp-var-dart-dt8mcustomboard-legacy-m7.dtb DART-MX8M-PLUS device tree blob for kernel >= 5.4.70 (Yocto Zeus) on on DT8MCustomBoard 1.x
imx8mp-var-som-symphony-m7.dtb VAR-SOM-MX8M-PLUS device tree blob for kernels >= 5.4.70 (Yocto Zeus) on on Symphony-Board
imx8mp-var-som-symphony-2nd-ov5640m7.dtb VAR-SOM-MX8M-PLUS device tree blob for kernels >= 5.4.70 (Yocto Zeus) on on Symphony-Board with 2nd OV5640


Default M7 pins v1

Default M7 pins used by the demos are:

Function SoC balls DART-MX8M-PLUS pins DT8MCB pins VAR-SOM-MX8M-PLUS pins Symphony pins Notes
UART3 RX/TX AE6 / AJ4 J2.87 / J2.89 J12.11 / J12.13
UART4 RX/TX AH5 / AJ5 J1.115 / J1.171 J18.9 / J18.7
GPIO3_IO14 R26 J1.79 J17.10
GPIO4_IO03 AF10 J2.59 GPLED1 on DT8MCB rev 1.x
J11.20 on DT8MCB rev 2.x
I2C3 SCL/SDA AJ7 / AJ6 J3.46 / J3.42 J12.18/ J12.20
I2C4 SCL/SDA AF8 / AD8 J1.92 / J1.90 J16.13 / J16.15 Enabling it SPI devices will be no longer visible from Linux
PWM2 D8 J1.69 J18.2
PWM3 AE18 J3.36 J14.7
SPI1 CS0/SCK/SDI/SDO AE20 / AF20 / AD20 / AC20 J2.79 / J2.77 / J2.81 / J2.83 J16.4/ J16.2 / J16.8 / J16.6 Enabling it SPI devices will be no longer visible from Linux
SPI2 CS0/SCK/SDI/SDO AJ22 / AH21 / AH20 / AJ21 J1.39 / J1.43 / J1.41 / J1.45 J16.4/ J16.2 / J16.6 / J16.8 Enabling it SPI devices will be no longer visible from Linux
FLEXCAN1 RX/TX AH15 / AJ16 j2.56 / j2.50 J13.11 / J13.5 on DT8MCB rev 1.x, TTL levels (CAN transceiver not mounted!) Enabling it FLEXCAN1 devices will be no longer visible from Linux
J16.9 / J16.7 on DT8MCB rev 2.x, CANL/CANH levels (CAN transceiver mounted!)
FLEXCAN2 RX/TX AJ4 / AE6 J1.46 / J1.44 J16.18 / J16.20, CANL/CANH levels (CAN transceiver mounted!) Enabling it FLEXCAN2 devices will be no longer visible from Linux

Available Demos

  • driver_examples/i2c/interrupt_b2b_transfer/slave
  • driver_examples/i2c/interrupt_b2b_transfer/master
  • driver_examples/i2c/polling_b2b_transfer/slave
  • driver_examples/i2c/polling_b2b_transfer/master
  • driver_examples/wdog
  • driver_examples/sdma/scatter_gather
  • driver_examples/sdma/memory_to_memory
  • driver_examples/gpio/led_output
  • driver_examples/pwm
  • driver_examples/uart/auto_baudrate_detect
  • driver_examples/uart/interrupt
  • driver_examples/uart/interrupt_rb_transfer
  • driver_examples/uart/polling
  • driver_examples/uart/interrupt_transfer
  • driver_examples/gpt/timer
  • driver_examples/gpt/capture
  • driver_examples/ecspi/ecspi_loopback
  • driver_examples/ecspi/interrupt_b2b_transfer/slave
  • driver_examples/ecspi/interrupt_b2b_transfer/master
  • driver_examples/ecspi/polling_b2b_transfer/slave
  • driver_examples/ecspi/polling_b2b_transfer/master
  • driver_examples/rdc
  • driver_examples/tmu/monitor_threshold
  • driver_examples/tmu/temperature_polling
  • driver_examples/sema4/uboot
  • rtos_examples/freertos_ecspi/ecspi_loopback
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_uart
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer
  • rtos_examples/freertos_i2c
  • cmsis_driver_examples/i2c/int_b2b_transfer/slave
  • cmsis_driver_examples/i2c/int_b2b_transfer/master
  • cmsis_driver_examples/uart/interrupt_transfer
  • cmsis_driver_examples/ecspi/int_loopback_transfer
  • cmsis_driver_examples/ecspi/sdma_loopback_transfer
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • demo_apps/hello_world
  • driver_examples/uart/idle_detect_sdma_transfer
  • driver_examples/uart/sdma_transfer
  • cmsis_driver_examples/uart/sdma_transfer

Variscite Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M7 as described in related linker file.

memory type M7 memory area A53 memory area memory lentgh linker file
DDR 0x80000000-0x801FFFFF (code)
0x80200000-0x803FFFFF (data)
0x80400000-0x80FFFFFF (data2) 		0x80000000-0x801FFFFF (code)
0x80200000-0x803FFFFF (data)
0x80400000-0x80FFFFFF (data2) 		16MB (DDR) MIMX8MN6xxxxx_cm7_ddr_ram.ld
TCM 0x00000000-0x0001FFFF (code)
0x20000000-0x2001FFFF (data)
0x80000000-0x80FFFFFF (data2) 		0x007E0000-0x007FFFFF (code)
0x00800000-0x0081FFFF (data)
0x80000000-0x80FFFFFF (data2) 		256kB (TCM) + 16MB (DDR) MIMX8MN6xxxxx_cm7_ram.ld

All linker files are locate in the armgcc folder of each demo.

The DDR reserved area must match the one declared in the kernel device tree: at least 1 GB of RAM is required on the SoM to allow Cortex-M7 accessing the range 0x80000000 - 0x80FFFFFF.

The RPMSG area is located at 0x40000000: all SoMs allow Cortex-M7 accessing the RPMSG area.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8M Plus Applications Processor Reference Manual paragraphs:

  • 2.2 Cortex-A53 Memory Map
  • 2.3 Cortex-M7 Memory Map

JTAG

The VAR-SOM-MX8M-PLUS exposes JTAG interface via an optional 10-pin header, on the SOM top left side.
The DART-MX8M-PLUS exports JTAG interface via an optional 10-pin header, on the DT8MCustomBoard top side.

Here is the pinout:

pin signal description pin signal description
1 JTAG_VREF JTAG IO reference voltage,
connected to SOM_3V3_PER via 150 Ohm. 		2 JTAG_TMS JTAG Mode Select signal
3 GND Digital Ground 4 JTAG_TCK JTAG Clock signal,
include PD of 8.2K Ohm.
5 GND Digital Ground 6 JTAG_TDO JTAG Data Out signal
7 GND Digital Ground 8 JTAG_TDI JTAG Data In signal
9 JTAG_TRST_B JTAG Reset signal,
active low signal 		10 POR_B Programmer Reset,
used to put the SOC in reset state.

Please refer to SoM datasheet for further details.

Releases

mcuxpresso-2.9.0-mx8mp-v1.0

   *HARDWARE_NAME = DART-MX8M-PLUS
  • RELEASE_NAME = mcuxpresso-2.9.0-mx8mp-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.9.0_V1.0_DART-MX8M-PLUS
  • MCUXPRESSO_VERSION = 2.9.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.9.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/dart_mx8mp
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-PLUS_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M-PLUS_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-PLUS_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-PLUS_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M-PLUS_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MP.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MP
  • YOCTO_RELEASE_TAG = zeus-fsl-5.4.70_2.3.2-mx8mp-v1.1
  • SOM_CAN_SUPPORT_1GB_DDR = yes

mcuxpresso-2.10.0-mx8mp-v1.0

   *HARDWARE_NAME = DART-MX8M-PLUS
  • RELEASE_NAME = mcuxpresso-2.10.0-mx8mp-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.10.0_V1.0_DART-MX8M-PLUS
  • MCUXPRESSO_VERSION = 2.10.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.10.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10-2020q4/gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10-2020-q4-major-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10-2020-q4-major
  • BOARD_FOLDER = boards/dart_mx8mp
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-PLUS_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M-PLUS_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-PLUS_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-PLUS_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M-PLUS_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MP.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MP
  • YOCTO_RELEASE_TAG = hardknott-fsl-5.10.52_2.1.0-mx8mp-v1.2
  • SOM_CAN_SUPPORT_1GB_DDR = yes

mcuxpresso-2.11.1-mx8mp-v1.0

   *HARDWARE_NAME = DART-MX8M-PLUS
  • RELEASE_NAME = mcuxpresso-2.11.1-mx8mp-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.11.1_V1.0_DART-MX8M-PLUS
  • MCUXPRESSO_VERSION = 2.11.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.11.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.07/gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.07-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.07
  • BOARD_FOLDER = boards/dart_mx8mp
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-PLUS_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M-PLUS_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-PLUS_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-PLUS_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M-PLUS_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MP.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MP
  • YOCTO_RELEASE_TAG = hardknott-fsl-5.10.52_2.1.0-mx8mp-v1.2
  • SOM_CAN_SUPPORT_1GB_DDR = yes

mcuxpresso-2.12.1-mx8mp-v1.0

   *HARDWARE_NAME = DART-MX8M-PLUS
  • RELEASE_NAME = mcuxpresso-2.12.1-mx8mp-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.12.1_V1.0_DART-MX8M-PLUS
  • MCUXPRESSO_VERSION = 2.12.1
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.12.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.10/gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-10.3-2021.10
  • BOARD_FOLDER = boards/dart_mx8mp
  • DOCS_FOLDER = docs
  • PINS_SECTION = DART-MX8M-PLUS_PINS_SECTION
  • DEMOS_SECTION = DART-MX8M-PLUS_DEMOS_SECTION
  • DTBS_SECTION = DART-MX8M-PLUS_DTBS_SECTION
  • MEMORY_TYPES_SECTION = DART-MX8M-PLUS_MEMORY-TYPES_VAR_SECTION
  • JTAG_SECTION = DART-MX8M-PLUS_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for EVK-MIMX8MP.pdf
  • NXP_REFERENCE_KIT = EVK-MIMX8MP
  • YOCTO_RELEASE_TAG = mx8mp-yocto-kirkstone-5.15-2.0.x-v1.0
  • SOM_CAN_SUPPORT_1GB_DDR = yes

mcuxpresso-2.13.0-mx8mp-v1.0


VAR-SOM-MX8X

Sections

Available dtbs

To allow Cortex M4 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, containing m4 label in the name, using the fdt_file environment variable in U-Boot.

This device tree disables some of the base device tree nodes in order to avoid conflicts between the main processor and Cortex M4.

File Name
 Description
imx8qxp-var-som-symphony-sd-m4.dtb VAR-SOM-MX8 device tree blob for kernel >= 5.4.85 (Yocto Dunfell)
imx8qxp-var-som-symphony-m4.dtb VAR-SOM-MX8 device tree blob for kernel >= 5.4.85 (Yocto Dunfell)


Default M4 pins

Default M4 pins used by the demos are:

Function Pin
debug UART (UART2) RX: J18.5 / TX: J18.3
I2C (I2C3) SCL: J16.10 / SDA: J16.12
M4 GPIO (M40_GPIO0_IO00) J16.3
M4 PWM (M40_TPM0_CH0) J16.7

Available Demos

  • cmsis_driver_examples/lpi2c/int_b2b_transfer/slave
  • cmsis_driver_examples/lpi2c/int_b2b_transfer/master
  • cmsis_driver_examples/lpi2c/edma_b2b_transfer/slave
  • cmsis_driver_examples/lpi2c/edma_b2b_transfer/master
  • cmsis_driver_examples/lpuart/edma_transfer
  • cmsis_driver_examples/lpuart/interrupt_transfer
  • demo_apps/hello_world
  • driver_examples/edma/scatter_gather
  • driver_examples/edma/memory_to_memory
  • driver_examples/intmux
  • driver_examples/lpi2c/edma_b2b_transfer/slave
  • driver_examples/lpi2c/edma_b2b_transfer/master
  • driver_examples/lpi2c/interrupt_b2b_transfer/slave
  • driver_examples/lpi2c/interrupt_b2b_transfer/master
  • driver_examples/lpi2c/polling_b2b_transfer/slave
  • driver_examples/lpi2c/polling_b2b_transfer/master
  • driver_examples/lpi2c/read_accel_value_transfer
  • driver_examples/lpit
  • driver_examples/lpuart/edma_transfer
  • driver_examples/lpuart/interrupt_rb_transfer
  • driver_examples/lpuart/polling
  • driver_examples/lpuart/interrupt_transfer
  • driver_examples/rgpio/led_output
  • driver_examples/sema42/uboot
  • driver_examples/tpm/input_capture
  • driver_examples/tpm/dual_edge_capture
  • driver_examples/tpm/timer
  • driver_examples/tpm/simple_pwm
  • driver_examples/tpm/output_compare
  • driver_examples/tstmr
  • driver_examples/wdog32
  • mmcau_examples/mmcau_api
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer

Additional demos are available as reference code, but require HW/SW customization.

NXP Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M4 as described in related linker file.

memory type M4 memory area A35 memory area memory lentgh linker file
DDR 0x88000000-0x881FFFFF (code)
0x88200000-0x883FFFFF (data)
0x88400000-0x8FFFFFFF (data2) 		0x88000000-0x881FFFFF (code)
0x88200000-0x883FFFFF (data)
0x88400000-0x8FFFFFFF (data2) 		128MB (DDR) MIMX8QX6xxxFZ_cm4_ddr_ram.ld
TCM 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x88000000-0x8FFFFFFF (data2) 		0x34FE0000-0x34FFFFFF (code)
0x35000000-0x3501FFFF (data)
0x88000000-0x8FFFFFFF (data2) 		256kB (TCM) + 128MB (DDR) MIMX8QX6xxxFZ_cm4_ram.ld

All linker files are locate in the armgcc folder of each demo.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)

Further details about memory mapping are available in the following i.MX 8DualX/8DualXPlus/8QuadXPlus Applications Processor Reference Manual paragraphs:

  • 2.2 System Memory Map
  • 2.2.9 Cortex-M4 Memory Map

JTAG

The VAR-SOM-MX8X exposes JTAG interface via an optional 10-pin header

Here is the pinout:

pin signal description pin signal (ball) description
1 JTAG_VREF JTAG reference voltage (3.3V) 2 JTAG_TMS (AG35) JTAG Mode Select
3 GND Digital Ground 4 JTAG_TCK (AE31) JTAG Clock
5 GND Digital Ground 6 JTAG_TDO (AF32) JTAG Data Out
7 RTCK JTAG Return clock 8 JTAG_TDI (AH34) JTAG Data In
9 JTAG_TRST_B_CONN JTAG TAP reset 10 JTAG_SRST_B JTAG System reset

Please refer to SOM datasheet for further details.


Releases

mcuxpresso-2.5.2-mx8qx-v1.0

       *HARDWARE_NAME = VAR-SOM-MX8X
  • SOC_HAS_SCU = true
  • RELEASE_NAME = mcuxpresso-2.5.2-mx8qx-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.5.2_V1.0_VAR-SOM-MX8X
  • YOCTO_RELEASE_LINK = RELEASE_SUMO_V1.2_VAR-SOM-MX8X
  • MCUXPRESSO_VERSION = 2.5.2
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.5.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/7-2018q2/gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-7-2018-q2-update-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-7-2018-q2-update
  • BOARD_FOLDER = boards/som_mx8qx
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8X_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8X_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8X_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8X_MEMORY-TYPES_NXP_SECTION
  • JTAG_SECTION = VAR-SOM-MX8X_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for i.MX 8QuadXPlus.pdf
  • NXP_REFERENCE_KIT = IMX8QXP-MEK
  • SCFW_SOC = = mx8qx_b0
  • SCFW_PATCH_URL = = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/SCFW
  • SCFW_M4_PATCH = = 0002-mx8qxp-var-som_scfw-1.2.2_sample-M4-customization.diff
  • IMX_MKIMAGE_SOC = = iMX8QX

mcuxpresso-2.8.0-mx8qx-v1.0

     *HARDWARE_NAME = VAR-SOM-MX8X
  • SOC_HAS_SCU = true
  • RELEASE_NAME = mcuxpresso-2.8.0-mx8qx-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.8.0_V1.0_VAR-SOM-MX8X
  • YOCTO_RELEASE_LINK = RELEASE_SUMO_V1.2_VAR-SOM-MX8X
  • MCUXPRESSO_VERSION = 2.8.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.8.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/som_mx8qx
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8X_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8X_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8X_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8X_MEMORY-TYPES_NXP_SECTION
  • JTAG_SECTION = VAR-SOM-MX8X_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for MEK-MIMX8QX.pdf
  • NXP_REFERENCE_KIT = IMX8QXP-MEK
  • SCFW_SOC = = mx8qx_b0
  • SCFW_PATCH_URL = = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/SCFW
  • SCFW_M4_PATCH = = 0002-mx8qxp-var-som_scfw-1.2.2_sample-M4-customization.diff
  • IMX_MKIMAGE_SOC = = iMX8QX
  • SDK_GIT_TAG = som-mx8qx_mcuxpresso-2.8.0_v10
  • RELEASE_DATE = 02/18/2021
  • SUPPORTED_REV_SOM = v1.1 and higher
  • SUPPORTED_REV_CARRIER = v1.1 and higher
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8x-v1.0

mcuxpresso-2.9.0-mx8qx-v1.0

     *HARDWARE_NAME = VAR-SOM-MX8X
  • SOC_HAS_SCU = true
  • RELEASE_NAME = mcuxpresso-2.9.0-mx8qx-v1.0
  • RELEASE_LINK = MCUXPRESSO_2.9.0_V1.0_VAR-SOM-MX8X
  • YOCTO_RELEASE_LINK = RELEASE_SUMO_V1.2_VAR-SOM-MX8X
  • MCUXPRESSO_VERSION = 2.9.0
  • SDK_PATH = ~/var-mcuxpresso
  • SDK_GIT_URL = https://github.com/varigit/freertos-variscite
  • SDK_GIT_BRANCH = mcuxpresso_sdk_2.9.x-var01
  • TOOLCHAIN_URL = https://developer.arm.com/-/media/Files/downloads/gnu-rm/9-2020q2/gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_BZ2_NAME = gcc-arm-none-eabi-9-2020-q2-update-x86_64-linux.tar.bz2
  • TOOLCHAIN_FOLDER = gcc-arm-none-eabi-9-2020-q2-update
  • BOARD_FOLDER = boards/som_mx8qx
  • DOCS_FOLDER = docs
  • PINS_SECTION = VAR-SOM-MX8X_PINS_SECTION
  • DEMOS_SECTION = VAR-SOM-MX8X_DEMOS_SECTION
  • DTBS_SECTION = VAR-SOM-MX8X_DTBS_SECTION
  • MEMORY_TYPES_SECTION = VAR-SOM-MX8X_MEMORY-TYPES_NXP_SECTION
  • JTAG_SECTION = VAR-SOM-MX8X_JTAG_SECTION
  • NXP_USER_GUIDE = Getting Started with MCUXpresso SDK for MEK-MIMX8QX.pdf
  • NXP_REFERENCE_KIT = IMX8QXP-MEK
  • SCFW_SOC = = mx8qx_b0
  • SCFW_PATCH_URL = = ftp://customerv:Variscite1@ftp.variscite.com/VAR-SOM-MX8X/Software/SCFW
  • SCFW_M4_PATCH = = 0002-mx8qxp-var-som_scfw-1.2.2_sample-M4-customization.diff
  • IMX_MKIMAGE_SOC = = iMX8QX
  • SDK_GIT_TAG = som-mx8qx_mcuxpresso-2.9.0_v10
  • RELEASE_DATE = 03/04/2021
  • SUPPORTED_REV_SOM = v1.1 and higher
  • SUPPORTED_REV_CARRIER = v1.1 and higher
  • YOCTO_RELEASE_TAG = dunfell-fslc-5.4-2.1.x-mx8x-v1.0

VAR-SOM-MX8

Sections

Available dtbs

To allow Cortex M4 accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, containing m4 label in the name, using the fdt_file environment variable in U-Boot.

This device tree disables some of the base device tree nodes in order to avoid conflicts between the main processor and Cortex M4.

File Name
 Description
imx8qm-var-som-symphony-dp-m4.dtb DTB file for VAR-SOM-MX8 with DP display and Cortex-M4 on Symphony Board for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-som-symphony-hdmi-m4.dtb DTB file for VAR-SOM-MX8 with HDMI display and Cortex-M4 on Symphony Board for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-som-symphony-lvds-m4.dtb DTB file for VAR-SOM-MX8 with LVDS display and Cortex-M4 on Symphony Board for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-spear-sp8customboard-dp-m4.dtb DTB file for SPEAR-MX8 with DP display and Cortex-M4 on SP8CustomBoard for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-spear-sp8customboard-hdmi-m4.dtb DTB file for SPEAR-MX8 with HDMI display and Cortex-M4 on SP8CustomBoard for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-spear-sp8customboard-lvds.m4.dtb DTB file for SPEAR-MX8 with LVDS display and Cortex-M4 on SP8CustomBoard for kernel >= 5.10.72 (Yocto Hardknott)
imx8qm-var-som-dp-m4.dtb DTB file for VAR-SOM-MX8 with DP display and Cortex-M4 on Symphony Board for kernel = 5.4.142 (Yocto Dunfell)
imx8qm-var-som-hdmi-m4.dtb DTB file for VAR-SOM-MX8 with HDMI display and Cortex-M4 on Symphony Board for kernel = 5.4.142 (Yocto Dunfell)
imx8qm-var-som-lvds-m4.dtb DTB file for VAR-SOM-MX8 with LVDS display and Cortex-M4 on Symphony Board for kernel = 5.4.142 (Yocto Dunfell)
imx8qm-var-spear-dp-m4.dtb DTB file for SPEAR-MX8 with DP display and Cortex-M4 on SP8CustomBoard for kernel = 5.4.142 (Yocto Dunfell)
imx8qm-var-spear-hdmi-m4.dtb DTB file for SPEAR-MX8 with HDMI display and Cortex-M4 on SP8CustomBoard for kernel = 5.4.142 (Yocto Dunfell)
imx8qm-var-spear-lvds-m4.dtb DTB file for SPEAR-MX8 with LVDS display and Cortex-M4 on SP8CustomBoard for kernel = 5.4.142 (Yocto Dunfell)


Default M4 pins

Default M4 pins used by the demos are:

Function SoC balls VAR-SOM-MX8 pins Symphony pins SPEAR-MX8 pins SP8CustomBoard pins Notes
M40_UART0 RX / TX AM44 / AU51 N/A N/A J3.32 / J3.38 J40 SP8CustomBoard requires SW8 ON, SW9 OFF
DMA_UART2 RX / TX BE35 / BE37 J1.175 / J1.124 J18.5 / J18.3 J1.80 / J1.82 J26.19 /J26.17
DMA_UART4 RX / TX AR47 / AU53 J1.115 / J1.171 J18.9 / J18.7 J3.34 / J3.29 J20.2 / J20.4 SPEAR-MX8 demos do not refer it
FLEXCAN0 RX/TX C5 / H6 J1.46 / J1.44 J16.18 / J16.20 J4.79 / J4.80 J26.1 / J26.3
M41_I2C0 SCL/SDA AR45 / AU49 N/A N/A J1.9 / J3.36 J20.18 / J20.20
DMA_I2C0 SCL/SDA BN9 / BN7 J1.174 / J1.176 J16.10 / J16.12 J2.88 / J1.90 J26.2 / J26.4
DMA_SPI0 CS0 / SCK / SDI / SDO BC1 / BB4 / BA5 / AY6 J1.79 / J1.75 / J1.77 / J1.70 J17.10 / J17.6 / J17.8 / J17.4 J2.78 / j2.74 / J2.72 / J2.76 J20.7 / J20.1 / J20.5 / J20.3
ADC_IN6 AL9 J1.39 J16.4 J4.62 J29.16 VAR-SOM-MX8 requires enabling a buffer (refer to the datasheet)
M40_TPM0 0 / 1 AR47 / AU53 J1.115 / J1.171 J18.9 / J18.7 J3.34 / J3.29 J20.2 / J20.4 pins are share with with DMA_UART4
GPIO3_IO06 BA3 J1.40 J17.2 J2.80 J20.9

Available Demos

  • cmsis_driver_examples/lpi2c/int_b2b_transfer/master
  • cmsis_driver_examples/lpi2c/int_b2b_transfer/slave
  • cmsis_driver_examples/lpi2c/edma_b2b_transfer/master
  • cmsis_driver_examples/lpi2c/edma_b2b_transfer/slave
  • cmsis_driver_examples/lpuart/edma_transfer
  • cmsis_driver_examples/lpuart/interrupt_transfer
  • cmsis_driver_examples/lpspi/edma_b2b_transfer/master
  • cmsis_driver_examples/lpspi/edma_b2b_transfer/slave
  • cmsis_driver_examples/lpspi/int_b2b_transfer/master
  • cmsis_driver_examples/lpspi/int_b2b_transfer/slave
  • demo_apps/hello_world
  • driver_examples/canfd/loopback_transfer
  • driver_examples/canfd/loopback
  • driver_examples/canfd/interrupt_transfer
  • driver_examples/edma/scatter_gather
  • driver_examples/edma/memory_to_memory
  • driver_examples/flexcan/loopback_edma_transfer
  • driver_examples/flexcan/loopback_transfer
  • driver_examples/flexcan/loopback
  • driver_examples/flexcan/interrupt_transfer
  • driver_examples/intmux
  • driver_examples/lpadc/interrupt
  • driver_examples/lpadc/polling
  • driver_examples/lpi2c/edma_b2b_transfer/slave
  • driver_examples/lpi2c/edma_b2b_transfer/master
  • driver_examples/lpi2c/interrupt_b2b_transfer/slave
  • driver_examples/lpi2c/interrupt_b2b_transfer/master
  • driver_examples/lpi2c/polling_b2b_transfer/slave
  • driver_examples/lpi2c/polling_b2b_transfer/master
  • driver_examples/lpi2c/read_accel_value_transfer
  • driver_examples/lpspi/edma_b2b_transfer/master
  • driver_examples/lpspi/edma_b2b_transfer/slave
  • driver_examples/lpspi/interrupt_b2b/master
  • driver_examples/lpspi/interrupt_b2b/slave
  • driver_examples/lpspi/interrupt_b2b_transfer/master
  • driver_examples/lpspi/interrupt_b2b_transfer/slave
  • driver_examples/lpspi/polling_b2b_transfer/master
  • driver_examples/lpspi/polling_b2b_transfer/slave
  • driver_examples/lpspi/polling_b2b_transfer/master
  • driver_examples/lpspi/polling_b2b_transfer/slave
  • driver_examples/lpit
  • driver_examples/lpuart/edma_transfer
  • driver_examples/lpuart/interrupt_rb_transfer
  • driver_examples/lpuart/polling
  • driver_examples/lpuart/interrupt_transfer
  • driver_examples/lpuart/interrupt
  • driver_examples/gpio/led_output
  • driver_examples/rgpio/led_output
  • driver_examples/sema42/uboot
  • driver_examples/sema42/dual_core
  • driver_examples/tpm/timer
  • driver_examples/tpm/simple_pwm
  • driver_examples/tpm/pwm_twochannel
  • driver_examples/tpm/output_compare
  • driver_examples/tpm/input_capture
  • driver_examples/tpm/dual_edge_capture
  • driver_examples/tpm/combine_pwm
  • driver_examples/tstmr
  • driver_examples/wdog32
  • mmcau_examples/mmcau_api
  • multicore_examples/rpmsg_lite_pingpong_rtos/linux_remote
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • multicore_examples/rpmsg_lite_pingpong_rtos/sdk_remote
  • multicore_examples/rpmsg_lite_pingpong_rtos/sdk_master
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_tickless
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_lpuart
  • rtos_examples/freertos_event
  • rtos_examples/freertos_swtimer
  • rtos_examples/freertos_lpi2c
  • rtos_examples/freertos_lpspi_b2b/master
  • rtos_examples/freertos_lpspi_b2b/slave
  • rtos_examples/freertos_lpspi

Additional demos are available as reference code, but require HW/SW customization.


NXP Memory types

The SDK allow linking using 2 different memory types: DDR, TCM.

Here is available a short summary of memory areas used by Cortex-M4 as described in related linker file.

memory type M4 if M4 memory area memory lentgh linker file
DDR 0 0x88000000-0x881FFFFF (code)
0x88200000-0x883FFFFF (data)
0x88400000-0x887FFFFF (data2) 		8MB (DDR) MIMX8QM6xxxFF_cm4_core0_ddr_ram.ld
DDR 1 0x88800000-0x88BFFFFF (code)
0x88C00000-0x88FFFFFF (data)
0x89000000-0x8FFFFFFF (data2) 		120MB (DDR) MIMX8QM6xxxFF_cm4_core1_ddr_ram.ld
TCM 0 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x88000000-0x887FFFFF (data2) 		256kB (TCM) + 8MB (DDR) MIMX8QM6xxxFF_cm4_core0_ram.ld
TCM 1 0x1FFE0000-0x1FFFFFFF (code)
0x20000000-0x2001FFFF (data)
0x88800000-0x8FFFFFFF (data2) 		256kB (TCM) + 120MB (DDR) MIMX8QM6xxxFF_cm4_core1_ram.ld

All linker files are locate in the armgcc folder of each demo.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • ddr_debug: containing DDR binaries compiled in debug mode (not stripped: symbols available)
  • ddr_release: containing DDR binaries compiled in release mode (stripped: no symbols available)
  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)


JTAG

The VAR-SOM-MX8 and SPEAR-MX8 exposes JTAG interface via an optional 10-pin header

Here is the pinout:

pin signal description pin signal (ball) description
1 JTAG_VREF JTAG reference voltage (3.3V) 2 JTAG_TMS (AG35) JTAG Mode Select
3 GND Digital Ground 4 JTAG_TCK (AE31) JTAG Clock
5 GND Digital Ground 6 JTAG_TDO (AF32) JTAG Data Out
7 RTCK JTAG Return clock 8 JTAG_TDI (AH34) JTAG Data In
9 JTAG_TRST_B_CONN JTAG TAP reset 10 JTAG_SRST_B JTAG System reset

Please refer to SOM datasheet for further details.

Releases

mcuxpresso-2.5.2-mx8qm-v1.0

      *HARDWARE_NAME = VAR-SOM-MX8

mcuxpresso-2.8.0-mx8qm-v1.0

    *HARDWARE_NAME = VAR-SOM-MX8

mcuxpresso-2.9.0-mx8qm-v1.0

    *HARDWARE_NAME = VAR-SOM-MX8


~/var-mcuxpresso/freertos-variscite/devices/MIMX8QM6


VAR-SOM-MX93

Sections

Available dtbs

To allow the Cortex-M33 to access shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded, by selecting the right version with the symbolic link in the /boot folder of the booting media.
These device trees contain m33 label in their name.


The below table lists an example dtb blob file name for VAR-SOM-MX93 (on the Symphony Board) with support for the M33 for each kernel version / Yocto release:

File Name
 Description
imx93-var-som-symphony-m33.dtb VAR-SOM-MX93 device tree blob for kernel = 6.1.1 (Yocto Langdale) on Symphony-Board 1.4a and above.

This device tree disables some of the base device tree nodes in order to avoid conflicts between the Cortex-A55 processors and Cortex-M33.

For the full list of device tree blob files, refer to the "Build Results" section in the appropriate wiki page for the specific Yocto/Debian release you are using.

Default M33 pins

Default M33 pins used by the demos are:

Function SoC balls VAR-SOM-MX8 Pins Symphony Pins Notes
UART7 RX/TX M21 / M20 J1.175 / J1.124 J18.5 / J18.3
TPM6-CH3 - PWM Output or Input Capture W21 J1.69 J18.2
CAN1 RX/TX J17 / G17 J1.46 / J1.44 J16.18 / J16.20, CANL/CANH levels (CAN transceiver mounted!) If enabled, CAN devices will no longer visible from Linux

Available Demos

  • demo_apps/ethosu_apps_rpmsg
  • demo_apps/hello_world
  • driver_examples/canfd/loopback
  • driver_examples/canfd/loopback_transfer
  • driver_examples/edma/memory_to_memory
  • driver_examples/edma/scatter_gather
  • driver_examples/edma4/channel_link
  • driver_examples/edma4/interleave_transfer
  • driver_examples/edma4/memory_to_memory
  • driver_examples/edma4/memory_to_memory_transfer
  • driver_examples/edma4/memset
  • driver_examples/edma4/ping_pong_transfer
  • driver_examples/edma4/scatter_gather
  • driver_examples/edma4/wrap_transfer
  • driver_examples/flexcan/loopback
  • driver_examples/flexcan/loopback_edma_transfer
  • driver_examples/flexcan/loopback_transfer
  • driver_examples/lpit/chained_channel
  • driver_examples/lpit/single_channel
  • driver_examples/lptmr
  • driver_examples/lpuart/interrupt
  • driver_examples/lpuart/interrupt_rb_transfer
  • driver_examples/lpuart/interrupt_transfer
  • driver_examples/lpuart/polling
  • driver_examples/tpm/input_capture
  • driver_examples/tpm/output_compare
  • driver_examples/tpm/simple_pwm
  • driver_examples/tpm/timer
  • driver_examples/tstmr
  • multicore_examples/rpmsg_lite_pingpong_rtos
  • multicore_examples/rpmsg_lite_str_echo_rtos
  • rtos_examples/freertos_event
  • rtos_examples/freertos_generic
  • rtos_examples/freertos_hello
  • rtos_examples/freertos_mutex
  • rtos_examples/freertos_queue
  • rtos_examples/freertos_sem
  • rtos_examples/freertos_swtimer

Additional demos may be provided on this platform in a future release.


Running a demo

Running a demo from U-Boot

To assist in loading m4 firmware from U-Boot prior to Linux boot, Variscite has created a dedicated set of U-Boot environment commands to assist in this.


To allow Cortex-M accessing shared resources without experiencing Linux kernel conflicts, a dedicated device tree must be loaded.

To enable Cortex-M U-Boot auto-loading: 

=> setenv use_m4 yes; saveenv

To disable Cortex-M U-Boot auto-loading: 

=> setenv use_m4 no; saveenv

To set the name of the Cortex-M binary 

=> setenv m4_bin cm_hello_world.bin; saveenv


The .bin file is expected in the folder /boot of the booting media.


After enabling as above, the U-Boot boot command will handle loading the Cortex-M firmware when the system begins the boot process. For testing, it is possible to invoke the m4 boot process manually: 

=> run loadm4bin && run runm4bin

Additional details and step by step procedure to run each of the demos is available online or in the following document: 

~/var-mcuxpresso/freertos-variscite/docs/Getting Started with MCUXpresso SDK for MEK-MIMX8QM.pdf


This process can be simplified using /etc/remoteproc/variscite-rproc-u-boot in Linux
Please refer to the Yocto Scripts section below for more information

Running a demo from Linux

The Linux remoteproc framework can be used to load the Cortex m4 firmware from Linux userspace.

Increase kernel loglevel while debugging: 

# sysctl kernel.printk=7;

Check the state of the m4, it should be running already by U-Boot 

# cat /sys/class/remoteproc/remoteproc0/state

If the state is 'running', stop the m4 

# echo stop > /sys/class/remoteproc/remoteproc0/state

Load new firmware (.elf file must already exist in /lib/firmware directory) 

# echo hello_world.elf > /sys/class/remoteproc/remoteproc0/firmware

Run the new firmware 

# echo start > /sys/class/remoteproc/remoteproc0/state


This process can be simplified using /etc/remoteproc/variscite-rproc-linux in Linux
Please refer to the Yocto Scripts section below for more information

NXP Memory types

The SDK currently allows linking only out of TCM.

Below is a short summary of memory areas used by Cortex-M33 as described in related linker file:

Memory Type M33 Memory Area A55 Memory Area Memory Length Linker File
TCM 0x0FFE0000 - 0x0FFFFFFF (code)
0x20000000 – 0x2001FFFF (data) 		0x201E0000 – 0x201FFFFF (code)
0x20200000 – 0x2021FFFF (data) 		128kB (Code TCM) + 128kB (System TCM) MIMX9352_cm33_ram.ld

All linker files are located in the armgcc folder of each demo. Please consult the linker file for the actual memory used by each demo.

After launching the build_all.sh command the following folder will be created in the armgcc folder

  • debug: containing TCM binaries compiled in debug mode (not stripped: symbols available)
  • release: containing TCM binaries compiled in release mode (stripped: no symbols available)


JTAG

The JTAG interface is not exposed directly on the VAR-SOM-MX93 but the associated signals are exposed via the J1 SOM connector.


Note: These signals are shared with the Wi-Fi module if present, so usage will require disabling this interface and making any appropriate pin muxing adjustments.

Please refer to SoM datasheet for further details.


Releases

mcuxpresso-2.13.1-mx93-v1.0


mcuxpresso-2.13.1-mx93-v1.1


mcuxpresso-2.15.0-mx93-v1.0


mcuxpresso-2.15.0-mx93-v1.1


Release Notes

RN_MCUXPRESSO_2.13.1_V1.0_VAR-SOM-MX93

|- | Release 1.0 || |- | Initial release || MCUXPRESSO 2.13.1 release for the Cortex-M33 core on the VAR-SOM-MX93 |- | Examples provided and tested on many peripherals: || - CAN
- EDMA
- LPUART
- TPM/PWM
- TSTMR

See developers guide for a full list of available demos. |-


RN_MCUXPRESSO_2.13.1_V1.1_VAR-SOM-MX93

|- | Release 1.1 || |- | Several additional examples provided for many peripherals: || - CAN (board to board examples)
- LPSPI
- LPI2C
- GPIO

See developers guide for a full list of available demos. |-


RN_MCUXPRESSO_2.15.0_V1.0_VAR-SOM-MX93

|- | Release 1.0 || |- | Initial release || MCUXPRESSO 2.15.0 release for the Cortex-M33 core on the VAR-SOM-MX93 |- style="vertical-align:top;" | Examples provided and tested on many peripherals: || - CAN (board to board examples)
- LPSPI
- EDMA
- LPI2C
- LPUART
- GPIO
- TPM/PWM
- TSTMR

See developers guide for a full list of available demos.
Click here for a full detailed change list. |-


RN_MCUXPRESSO_2.15.0_V1.1_VAR-SOM-MX93

|- | Release 1.1 || |- style="vertical-align:top;" | Add initial support for DART-MX93 || MCUXPRESSO 2.15.0 release for the Cortex-M33 core on the DART-MX93 - CAN (board to board examples)
- LPSPI
- EDMA
- LPI2C
- LPUART
- GPIO
- TPM/PWM
- TSTMR

See developers guide for a full list of available demos.
Click here for a full detailed change list. |- | Update macros and readme files for the VAR-SOM-MX93 release || See 8deddc3fc...78afa00fe |- | Known Issues || |- | driver_examples/rgpio/led_output demo does not work properly on U-boot on the DART-MX93 || When running on U-boot, it stops working right after Linux finishes booting |-

Retrieved from "https://variwiki.com/index.php?title=MCUXpresso_Platform_Customization&oldid=24056"
Latest Modules
Support
Variscite Support Center
Contact Support
Product Longevity
Product Compliance Policy
Blog
Variscite Training
Variscite Website
This page was last edited on 2 August 2023, at 20:52.

© 2024 Variscite. All rights reserved