B2QT VAR-SOM-MX8: Difference between revisions
From Variscite Wiki
(B2Qt Dunfell v1.2 release for VAR-SOM-MX8 and SPEAR-MX8) |
No edit summary |
||
Line 151: | Line 151: | ||
-->{{#vardefine:QT_VERSION|6.0.4}} <!-- | -->{{#vardefine:QT_VERSION|6.0.4}} <!-- | ||
--> <section end=mx8-b2qt-dunfell-5.4-2.1.x-v1.2/> | --> <section end=mx8-b2qt-dunfell-5.4-2.1.x-v1.2/> | ||
<includeonly><section begin=RELEASE_NOTES/> | |||
<section begin=RN_mx8-b2qt-dunfell-5.4-2.1.x-v1.2/> | |||
|- | |||
| <span {{#var:STYLE_RELEASE}}>Release 1.2</span> || | |||
|- | |||
| '''U-Boot''' || | |||
|- | |||
| imx8qm_var_som: enable RX clock delay for symphony ar8033 || | |||
|- | |||
| imx8qm_var_som: fec2: add new properties to align with Hardknott release || | |||
|- | |||
| imx8qm_var_som: fec1: tune phy-reset-post-delay with proper value || | |||
|- | |||
| variscite: extcon-ptn5150: add ptn5150 driver || | |||
|- | |||
| imx8qm-var-spear: fec: add 20ms phy-reset-post-delay || | |||
|- | |||
| variscite: eth: ADIN1300: Disable RGMII RX clock delay || | |||
|- | |||
| imx8qm-var-som: fix lvds_backlight_hog || | |||
|- | |||
| imx8qm_var_som: drop unused board_rev environment variable || | |||
|- | |||
| variscite: imx8_eeprom: drop VAR_EEPROM_F_LVDS and cleanup indentation || | |||
|- | |||
| '''Kernel''' || | |||
|- | |||
| imx8qm-var-som: configure symphony adi,phy-mode-overide to rgmii || | |||
|- | |||
| imx8qm-var-som: ethphy1: remove no need rx-internal-delay-ps property || | |||
|- | |||
| MLK-14644 PCI: imx: toggle the perst after the release of rc's reset || | |||
|- | |||
| imx8qm-var-som: fec: add phy-reset-post-delay || | |||
|- | |||
| net: phy: adin: add adi,phy-mode-override property || | |||
|- | |||
| imx8_var_defconfig: enable docker requirements || | |||
|- | |||
| imx8qm-var-som: dts: ethphy1: Add support for ADIN1300 PHY for VAR-SOM || | |||
|- | |||
| MLK-25674 mmc: sdhci-esdhc-imx: remove command queue feature support || | |||
|- | |||
| imx8_var_defconfig: enable driver for ADIN PHY || | |||
|- | |||
| imx8qm-var-som: refactor to drop imx8qp-var-common.dtsi || | |||
|- | |||
| <span {{#var:STYLE_RELEASE}}>Release 1.1</span> | |||
|- | |||
|'''U-Boot''' | |||
|- | |||
|imx8qm-var-som: Introduce support for the i.MX8QP SoC | |||
|- | |||
|imx8qm-var-som: Provide som_wifi kernel argument | |||
|- | |||
|imx8: ahab: Only compile ahab.c for u-boot | |||
|- | |||
|imx8 soms: Add USE_EMMC_BOOT_PART config to use user partition for fastboot | |||
|- | |||
|'''Kernel''' | |||
|- | |||
|Update kernel from version 5.4.85 to 5.4.142 | |||
|- | |||
|imx8_var_defconfig: add full docker support | |||
|- | |||
|imx8qm-var-som: Introduce support for the i.MX8QP SoC | |||
|- | |||
|imx8qm-var-som: enable internal pullups for i2c0, i2c1, i2c3, i2c4 | |||
|- | |||
|Revert "MLK-14801 input: touch: ads7846: fix the pressure_max setting" | |||
|- | |||
|sn65dsi83: Add device tree property to swap LVDS Channel A/B | |||
|- | |||
|imx8qm-var-spear: Adjust usb hsic pad settings | |||
|- | |||
|ARM: configs: Variscite: Enable USB_HSIC_USB3053 | |||
|- | |||
|ARM: configs: Variscite: disable EVBUG module | |||
|- | |||
|ARM64: dts: imx8: Variscite: add WM8904 DRC support for all SoMs | |||
|- | |||
|ASoC: wm8904: extend device tree support | |||
|- | |||
|'''meta-variscite-boot2qt''' | |||
|- | |||
|Update Qt from version 6.0.3 to 6.0.4 | |||
|- | |||
|manifest: meta-variscite-fslc: Update to latest | |||
|- | |||
|b2qt-embedded-qt6-image: Add libgpiod and libgpiod-tools | |||
|- | |||
|b2qt-embedded-qt5-image: allow disabling virtual terminals | |||
|- | |||
|Variscite: mask linux-firmware bbappend in meta-boot2qt-distro | |||
|- | |||
|Merge branch '6.0' into dunfell-var01 | |||
|- | |||
| <span {{#var:STYLE_RELEASE}}>Release 1.0</span> | |||
|- | |||
| First Release | |||
<section end=RN_mx8-b2qt-dunfell-5.4-2.1.x-v1.2/> | |||
<section end=RELEASE_NOTES/></includeonly> |
Revision as of 23:39, 6 July 2022
var-som-mx8-b2qt-v1.0
var-som-mx8-b2qt-v1.1
dunfell-b2qt-5.4-2.1.x-mx8-v1.0
dunfell-b2qt-5.4-2.1.x-mx8-v1.1
mx8-b2qt-dunfell-5.4-2.1.x-v1.2