Yocto Flash From Net: Difference between revisions

From Variscite Wiki
No edit summary
No edit summary
Line 1: Line 1:
<!-- Set release according to "release" parameter in URL and use MORTY_BETA_DART-6UL as default
<!-- Set release according to "release" parameter in URL and use MORTY_V1.0_DART-6UL as default
--> {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!--
--> {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!--
--> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_BETA_DART-6UL}}}} <!--
--> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!--
--> {{PageHeader|{{#var:HARDWARE_NAME}} - Flash Yocto images from network}} {{DocImage|category1={{#var:HARDWARE_NAME}}|category2=Yocto}} __toc__
--> {{PageHeader|{{#var:HARDWARE_NAME}} - Flash Yocto images from network}} {{DocImage|category1={{#var:HARDWARE_NAME}}|category2=Yocto}} __toc__



Revision as of 15:12, 24 December 2020

DART-6UL - Flash Yocto images from network

Flashing a complete Yocto system from Network using TFTP & NFS

NOTES:
  1. Please make sure your host system is ready to use TFTP/NFS. Use our Wiki if required: Yocto Setup TFTP/NFS
  2. This is a concept Wiki. Please adopt it to your system and your requirements.
  3. Android can be flashed in the same way.

Build minimal file system

To setup a Yocto build environment follow steps 1 & 3 of the Build Yocto from source code guide.
Then, append the following to the conf/local.conf file in your Yocto build directory:

IMAGE_INSTALL_append = " bash e2fsprogs-mke2fs tar mtd-utils imx-kobs mtd-utils-ubifs"

And build the image:

$ bitbake core-image-minimal

Create a root file system and copy files:

$ mkdir ~/flash_rootfs
$ sudo tar xf tmp/deploy/images/imx6ul-var-dart/core-image-minimal-imx6ul-var-dart.tar.gz -C ~/flash_rootfs
$ sudo cp tmp/deploy/images/imx6ul-var-dart/zImage /tftpboot
$ for f in tmp/deploy/images/imx6ul-var-dart/*.dtb; do if [[ -L $f ]] && [[ $f != *imx6ul-var-dart.dtb ]]; then sudo cp $f /tftpboot/; fi done
$ sudo rename 's/zImage-imx/imx/' /tftpboot/zImage-*.dtb

Insert the recovery SD card into your host PC and copy the following files from it (assuming it is mounted at /media):

$ sudo cp -a /media/rootfs/opt/images ~/flash_rootfs/opt/
$ sudo cp /media/rootfs/usr/bin/*.sh  ~/flash_rootfs/usr/bin/

Boot the board, stop the autoboot to get to the U-Boot command line, and set the following environment variables:

=> setenv serverip <your host ip address>
=> setenv nfsroot /home/<your username>/flash_rootfs

If you want to set the fdt file yourself, instead of using the default auto detection:
=> setenv fdt_file <relevant device tree>
=> setenv bootcmd 'run netboot'
=> saveenv
=> boot

On the target flash your system:

# install_yocto.sh

A complete system is flashed into the SOMs internal storage (NAND flash/eMMC).
Once the file system is built you can use it again and again to flash your DART-6UL.
You can update the images to use your images and/or customize install_yocto.sh to your requirements.