Dual Display

Dual Display on VAR-SOM-SOLO/DUAL / DART-MX6 : Android Application Tech Note.

IMX6 platform is capable of handling multiple displays. You can drive

See page : 15 - 19 http://cache.freescale.com/files/training/doc/ftf/2014/FTF-CON-F0119.pdf

Starting from Android 4.3 multiple displays are supported

DART-MX6 / Solo both have LVDS0 and LVDS1 output available on the development board.

VAR-DT6CustomBoard:

For both channels: LVDS0/1 - LVDS Clock +4 Data lanes are accessible via Carrier board Headers.

VAR-SOLOCustomBoard:

LVDS0 - LVDS Clock +4 Data lanes are accessible via Carrier board Headers.

LVDS1 - LVDS Clock +3 Data lanes are accessible via Carrier board Headers (only 18 bit LCD can be interfaced)

For maximum supported resolution and combination refer to

http://cache.freescale.com/files/training/doc/ftf/2014/FTF-CON-F0119.pdf age no 16.

The configuration can be like

1. Clone display (Primary is always cloned)
2. Independent display

In case of 1. The kernel will not register another framebuffer for 2nd panel, however clone internally from the SOC itself via IPU framebuffer driver from the interface specific drivers. Aka LDB, HDMI, RGB.

In case of 2. The kernel registers 2nd FB to the platform.

Use case Two LVDS - LVDS0 and LVDS1 port on SOLO

• Hardware Setup

2 x LVDS Panel : https://www.variscite.com/products/accessories/vlcd-cap-gld-lvds/

Reference : https://www.variscite.com/wp-content/uploads/2017/12/VLCD-CAP-GLD-LVDS.pdf

Connect 1st panel to LVDS1 - which is enabled by default with the software. Connect straight LVDS panel header to LVDS1 as this doesn’t require special handling.

Connect 2nd panel to LVDS0 - which requires changes in the software.

This example uses an identical LVDS panel however you can have an asymmetric combination as well.

Top level setup should look like below

Using wires connect LVDS0 to LVDS header in the LCD panel with the following combination.

Pin to pin as shown in the below with color coded.

PIN	LVDS0 PIN - J16		PIN	PIN	LVDS LCD Panel Header		PIN
1	3.3 V	3.3 V	2	1	VCC - 3V	VCC - 3V	2
3	GND	GND	4	3	GND	GND	4
5	LVDS0_TX0_N	LVDS0_TX0_P	6	5	RIN0_N	RIN0_P	6
7	GND	LVDS0_TX1_N	8	7	GND	RIN1_N	8
9	LVDS0_TX1_P	GND	10	9	RIN1_P	GND	10
11	LVDS0_TX2_N	LVDS0_TX2_P	12	11	RIN2_N	RIN2_P	12
13	GND	LVDS0_CLK_N	14	13	GND	RCLK_N	14
15	LVDS0_CLK_P	GND	16	15	RCLK_P	GND	16
17	LVDS0_TX3_N	LVDS0_TX3_P	18	17	5V_CC_Backlight	5V_CC_Backlight	18
19	VCC_5V	PWM_BACK_LIGHT	20	19	PWM_INPUT	GND	20

Note :

• LVDS0 provides 3 lanes but LCD just needs 2 lane LVDS input.
• Warning! Be careful about PIN 19 of LVDS0 header, please make sure it is connected to PIN17 or PIN18 of the LCD panel header only. Connecting this pin to other pins of LCD or shorting to GND may cause permanent damage to LCD or board.

Software Changes for Multiple Display:

Android Oreo 8.0 and Android 7.1.2 :

• Software Preparation for Dual Display (Two LVDS):

1. U-Boot: On U-Boot you require below patch to be applied.

For Android 8.0: vendor/variscite/uboot-imx/

For Android 7.1.2: bootable/bootloader/uboot-imx/

diff --git a/board/variscite/mx6var_som/mx6var_som.c b/board/variscite/mx6var_som/mx6var_som.c
index 526a11f..729c966 100644
--- a/board/variscite/mx6var_som/mx6var_som.c
+++ b/board/variscite/mx6var_som/mx6var_som.c
@@ -907,7 +907,7 @@ static void setup_display(void)
              | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
              | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
              | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
-             | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+             | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
              | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0
              | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0;
         writel(reg, &iomux->gpr[2]);
diff --git a/include/configs/mx6var_som.h b/include/configs/mx6var_som.h
index 1db7afb..b27f7ee 100644
--- a/include/configs/mx6var_som.h
+++ b/include/configs/mx6var_som.h
@@ -195,7 +195,7 @@
                                 "video=mxcfb0:dev=ldb; " \
                 "fi; " \
                 "setenv bootargs ${bootargs} " \
-                        "video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off;\0"
+                        "video=mxcfb1:dev=ldb video=mxcfb2:off video=mxcfb3:off;\0"

 #define CONFIG_EXTRA_ENV_SETTINGS \

Please take a note here, we enable channel 0 for solo, as 18 bit and enable fb1 set the device to LDB(LVDS).

1. Kernel:

For Android 8.0: ~/var_o_800_100/imx-o8.0.0_1.0.0_ga/android_build/kernel_imx

For Android 7.1.2: ~/var_n_712_200/n_712_200_build/kernel_imx

diff --git a/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi b/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
index 8876245..b329e9d 100644
--- a/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
@@ -12,6 +12,14 @@
        interface_pix_fmt = "RGB666";
 };

+&mxcfb2 {
+       disp_dev = "ldb";
+       interface_pix_fmt = "RGB666";
+       default_bpp = <16>;
+       int_clk = <0>;
+       late_init = <0>;
+};
+
 &i2c3 {
        touch: ft5x06_ts@38 {
                compatible = "edt,edt-ft5x06";
@@ -28,22 +36,21 @@

        lvds-channel@0 {
                fsl,data-mapping = "spwg";
-               fsl,data-width = <24>;
-               crtc = "ipu1-di0";
+               fsl,data-width = <18>;
                status = "okay";

                display-timings {
                        native-mode = <&timing0>;
                        timing0: hsd100pxn1 {
-                               clock-frequency = <35714000>;
+                               clock-frequency = <32000000>;
                                hactive = <800>;
                                vactive = <480>;
-                               hback-porch = <24>;
-                               hfront-porch = <15>;
-                               vback-porch = <13>;
-                               vfront-porch = <20>;
-                               hsync-len = <20>;
-                               vsync-len = <13>;
+                               hback-porch = <39>;
+                               hfront-porch = <39>;
+                               vback-porch = <29>;
+                               vfront-porch = <13>;
+                               hsync-len = <47>;
+                               vsync-len = <2>;
                        };
                };
        };

@@ -51,7 +58,6 @@
        lvds-channel@1 {
                fsl,data-mapping = "spwg";
                fsl,data-width = <18>;
-               crtc = "ipu1-di1";
                primary;
                status = "okay";

• Software Preparation for Dual Display (LVDS + HDMI):
• Kernel:

For Android 8.0: ~/var_o_800_100/imx-o8.0.0_1.0.0_ga/android_build/kernel_imx

Compile the kernel with following changes in the device tree below.

http://variwiki.com/index.php?title=VAR-SOM-MX6_Android&release=RELEASE_O8.0.0_1.0.0_VAR-SOM-MX6#Build_boot.img

For Android 7.1.2: ~/var_n_712_200/n_712_200_build/kernel_imx

Compile the kernel with following changes in the device tree below

http://variwiki.com/index.php?title=VAR-SOM-MX6_Android&release=RELEASE_N7.1.2_2.0.0_VAR-SOM-MX6#Build_boot.img

Device Tree Changes :

diff --git a/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi b/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
index 8876245..7332dcb 100644
--- a/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-var-solocb-dt6cb-displays.dtsi
@@ -29,7 +29,6 @@
        lvds-channel@0 {
                fsl,data-mapping = "spwg";
                fsl,data-width = <24>;
-               crtc = "ipu1-di0";
                status = "okay";

                display-timings {
@@ -51,7 +50,6 @@
        lvds-channel@1 {
                fsl,data-mapping = "spwg";
                fsl,data-width = <18>;
-               crtc = "ipu1-di1";
                primary;
                status = "okay";

Install the boot image to respective platform and then at U-Boot prompt change the bootargs

U-Boot prompt commands :

=> setenv videoargs 'setenv bootargs ${bootargs} video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 video=mxcfb1:dev=ldb consoleblank=0 video=mxcfb2:off video=mxcfb3:off;'

=> saveenv

=> reset

3) Android Framework changes (Optional) for Android 8.0 only:

If you wish to have activities to be launched on secondary panel

Add the line <feature name="android.software.activities_on_secondary_displays" /> to tablet_core_hardware.xml

This file is located at /system/etc/permissions/ on the Android

On the source side, the file is located at

For Android 8.0: android_build/variscite/var_mx6/tablet_core_hardware.xml

This feature is required for setLaunchDisplayId(<display number>) to work.

4) Compile the image for your platform following

For Android 8.0 :

http://variwiki.com/index.php?title=VAR-SOM-MX6_Android&release=RELEASE_O8.0.0_1.0.0_VAR-SOM-MX6#Build_Android_Images

For Android 7.1.2 :

http://variwiki.com/index.php?title=VAR-SOM-MX6_Android&release=RELEASE_N7.1.2_2.0.0_VAR-SOM-MX6#Build_Android_Images

and program the image to VAR-SOM-SOLO/DUAL or DART-MX6

Testing: By default Android operates in clone mode, but if you wish to have two different content on two different panels; your Android application must explicitly tell which display it wants to render the Surface. You can use the presentation mode.

Customer should be advised to use the presentation mode for testing / prototyping.

More information about presentation mode available here : https://developer.android.com/reference/android/app/Presentation

Reference :

<Your_Android_Build>/development/samples/ApiDemos->./src/com/example/android/apis/app/PresentationWithMediaRouterActivity.java is sample code.

If you wish to make apk for ApiDemos,

For Android 8.0:

$ cd ~/var_o_800_100/imx-o8.0.0_1.0.0_ga/android_build$ source build/envsetup.sh$ lunch var_mx6-engor$ lunch var_mx6-userdebug

$ cd development/samples/ApiDemos

mm

This should generate out/target/product/var_mx6/testcases/ApiDemos/ApiDemos.apk copy apk to your present directory from which you can install on the platform

Connect OTG and use adb to install using below command.

$adb install ApiDemos.apk

For Android 7.1.2:

$ cd ~/var_n_712_200/n_712_200_build$ source build/envsetup.sh$ lunch var_mx6-engor$ lunch var_mx6-user

$ cd development/samples/ApiDemos

mm

This will generate apk on out/target/product/var_mx6/data/app/ApiDemos/ApiDemos.apk path which you can install on the platform. Copy apk to your present directory from which you can install on the platform.

$adb install ApiDemos.apk

Note: For LVDS + HDMI case, at command prompt run below commands

# echo 0 > /sys/class/graphics/fb2/blank

By default, Android will clone the primary display to secondary unless you specify in the application layer for which display to use using presentation mode.

Your screen should look like this after installation

[[Image:]]

Click on API Demos

[[Image:]]

Click on App should give you screen as below

[[Image:]]

Click on Activity Should give you screen as below

[[Image:]]

Click on Presentation with Media Router

Once you do that you should see the output on 2nd panel different than the first panel like below

[[Image:]]

Here in the left side is a secondary panel (LVDS0) and right side which is a primary panel (LVDS1).

• 

  Left Screen(LVDS0)

• 

  Right Screen(LVDS1)

Note :

• In case of LVDS + HDMI the HDMI is your primary panel so you will see spinning cubes on the LVDS and Android main UI on HDMI monitor.