VAR-SOM-MX6 Yocto Flash From Net: Difference between revisions

From Variscite Wiki
No edit summary
 
Line 26: Line 26:
<pre>
<pre>
$ mkdir ~/flash_rootfs
$ mkdir ~/flash_rootfs
$ sudo tar xvf tmp/deploy/images/varsomimx6/core-image-minimal-mtdutils-varsomimx6.tar.bz2 -C ~/flash_rootfs
$ sudo tar xvf tmp/deploy/images/var-som-mx6/core-image-minimal-mtdutils-var-som-mx6.tar.bz2 -C ~/flash_rootfs
$ sudo cp tmp/deploy/images/varsomimx6/uImage /tftpboot
$ sudo cp tmp/deploy/images/var-som-mx6/uImage /tftpboot
$ sudo cp tmp/deploy/images/varsomimx6/uImage-imx6dl-var-som.dtb /tftpboot/imx6dl-var-som.dtb
$ sudo cp tmp/deploy/images/var-som-mx6/uImage-imx*.dtb /tftpboot/
$ sudo cp tmp/deploy/images/varsomimx6/uImage-imx6dl-var-som-solo.dtb /tftpboot/imx6dl-var-som-solo.dtb
$ sudo rename 's/uImage-//' /tftpboot/uImage-*
$ sudo cp tmp/deploy/images/varsomimx6/uImage-imx6q-var-som.dtb /tftpboot/imx6q-var-som.dtb
</pre>
</pre>


Insert nand-recovery into your host and copy files
Insert the recovery SD card into your host PC and copy the following files from it (assuming it is mounted at /media):
<pre>
<pre>
$ sudo mkdir ~/flash_rootfs
$ sudo mkdir ~/flash_rootfs
$ sudo cp -a /media/rootfs/opt/images ~/flash_rootfs/opt/
$ sudo cp -a /media/rootfs/opt/images ~/flash_rootfs/opt/
$ sudo cp /media/rootfs/sbin/nand-recovery.sh ~/flash_rootfs/sbin/
$ sudo cp /media/rootfs/usr/bin/*.sh ~/flash_rootfs/usr/bin
</pre>
</pre>


Boot into U-Boot and change environment variables
Boot the board, stop the autoboot to get to the U-Boot command line, and set the following environment variables:
<pre>
<pre>
$ setenv serverip <your host ip address>
=> setenv serverip <your host ip address>
$ setenv bootfile uImage
=> setenv bootfile uImage
$ setenv nfsroot /ws/ron/yocto-dora-fsl-beta/rootfs_min
=> setenv nfsroot /home/<your username>/flash_rootfs
$ setenv console ttymxc0
=> setenv console ttymxc0
$ setenv bootcmd 'run netboot'
=> setenv bootcmd 'run netboot'
$ boot
=> boot
</pre>
</pre>


On the target flash your system:
On the target flash your system:
<pre>
<pre>
$ nand-recovery.sh
$ install_yocto.sh
</pre>
</pre>


A complete system is flashed into nand. Once the file system is built you can use it again and again to flash your VAR-SOM-MX6. You can update the images to use your images or custom nand-recovery.sh to your requirements.
A complete system is flashed into nand. Once the file system is built you can use it again and again to flash your VAR-SOM-MX6. You can update the images to use your images or custom nand-recovery.sh to your requirements.

Latest revision as of 08:28, 7 June 2017

Flash From Network Yocto system

Flashing a complete Yocto system from Network using TFTP & NFS

NOTES:
  1. Please make sure your host system is ready to use TFTP/NFS. Use our WIKI if required: TFTP & NFS
  2. Mix and match the nand-recovery version with the system you would like to flash.
  3. This is a concept Wiki. Please adopt it to your system and your requirements.
  4. Android can be flashed in the same way.

Build minimal file system

$ gedit ../sources/poky/meta/recipes-core/images/core-image-minimal-mtdutils.bb

Set the image to include: IMAGE_INSTALL += "mtd-utils imx-kobs mtd-utils-ubifs"
Build the system:

$ bitbake core-image-minimal-mtdutils

Create a root file system and copy files

$ mkdir ~/flash_rootfs
$ sudo tar xvf tmp/deploy/images/var-som-mx6/core-image-minimal-mtdutils-var-som-mx6.tar.bz2 -C ~/flash_rootfs
$ sudo cp tmp/deploy/images/var-som-mx6/uImage /tftpboot
$ sudo cp tmp/deploy/images/var-som-mx6/uImage-imx*.dtb /tftpboot/
$ sudo rename 's/uImage-//' /tftpboot/uImage-*

Insert the recovery SD card into your host PC and copy the following files from it (assuming it is mounted at /media):

$ sudo mkdir ~/flash_rootfs
$ sudo cp -a /media/rootfs/opt/images ~/flash_rootfs/opt/
$ sudo cp /media/rootfs/usr/bin/*.sh ~/flash_rootfs/usr/bin

Boot the board, stop the autoboot to get to the U-Boot command line, and set the following environment variables:

=> setenv serverip <your host ip address>
=> setenv bootfile uImage
=> setenv nfsroot /home/<your username>/flash_rootfs
=> setenv console ttymxc0
=> setenv bootcmd 'run netboot'
=> boot

On the target flash your system:

$ install_yocto.sh

A complete system is flashed into nand. Once the file system is built you can use it again and again to flash your VAR-SOM-MX6. You can update the images to use your images or custom nand-recovery.sh to your requirements.