Yocto Build U-Boot: Difference between revisions
From Variscite Wiki
No edit summary |
(Replace more nested ifs) |
||
| Line 124: | Line 124: | ||
{{#ifeq: {{#var:SOC_FAMILY}}| imx8m | | {{#ifeq: {{#var:SOC_FAMILY}}| imx8m | | ||
{{#ifeq: {{#var:FSL_BSP_VERSION}}| L4.14.78-1.0.0_ga | $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | | {{#ifeq: {{#var:FSL_BSP_VERSION}}| L4.14.78-1.0.0_ga | $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | | ||
{{# | {{#switch: {{#var:SOC}}|mx8mn= $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | ||
| mx8mp= $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | |||
| mx8mm= $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8mm* ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-* | | |||
| mx8mq= $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-*}} }} }} | |||
$ source {{#var:TOOLCHAIN_LOCATION}} | $ source {{#var:TOOLCHAIN_LOCATION}} | ||
$ unset LDFLAGS | $ unset LDFLAGS | ||
Revision as of 23:54, 6 January 2023
Yocto Build U-Boot from source code
Toolchain installation for out of Yocto builds
To install the toolchain, follow Yocto Toolchain installation.
Build U-Boot out of Yocto tree
Obtain sources:
$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03 $ cd uboot-imx
Configure compilation environment:
$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi
Cleanup everything:
$ make mrproper
Select one of the following configurations:
For booting from SD card/eMMC: $ make mx6var_som_sd_defconfig For booting from NAND flash: $ make mx6var_som_nand_defconfig
Build U-Boot:
$ make -j$(nproc)
{{#ifeq: | imx8 |
Build boot image
The final boot image contains multiple firmware files. The following procedure builds the final image.
Create imx-boot-tools directory:
$ mkdir imx-boot-tools $ cd imx-boot-tools
Download DDR firmware:
$ wget /.bin $ chmod +x .bin $ ./.bin $ cp /firmware/ddr/synopsys/* .
Download imx_mkimage:
$ git clone /imx-mkimage -b $ cp imx-mkimage/iMX8M/*.c imx-mkimage/iMX8M/*.sh . $
Download and build ATF:
$ git clone /imx-atf -b $ cd imx-atf $ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi $ unset LDFLAGS $ make PLAT= bl31 $ cp build//release/bl31.bin .. $ cd ..
Copy U-Boot binaries:
$ cp ../tools/mkimage mkimage_uboot $ cp ../u-boot.bin . $ cp ../spl/u-boot-spl.bin .
Install the built U-Boot on an SD card
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync $ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync (Replace /dev/sdX with the correct device)
If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:
$ sudo cp SPL /media/rootfs/opt/images/… $ sudo cp u-boot.img /media/rootfs/opt/images/…
And eject the SD card gracefully from host machine.
Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)
Update your U-Boot out of Yocto tree
$ git pull