Imx uuu: Difference between revisions
No edit summary |
|||
Line 35: | Line 35: | ||
'''Boot the board into serial download mode''':<br> | '''Boot the board into serial download mode''':<br> | ||
*{{Varlink|Yocto_Build_Release#Setting the Boot Mode|{{#var:RELEASE_LINK}}|Set the board boot mode}} to SD card, while not having an actual card inserted in its slot.<br> | *{{Varlink|Yocto_Build_Release#Setting the Boot Mode|{{#var:RELEASE_LINK}}|Set the board boot mode}} to SD card, while not having an actual card inserted in its slot.<br> | ||
Alternatively, set the board boot mode to eMMC/NAND flash, when the eMMC/NAND flash does not contain a bootloader.<br> | |||
Connect the board to your host PC via the USB OTG port, and power on the board.<br> | |||
The board should be recognized on the host as a "NXP Semiconductors SE Blank M850" (or something similar).<br> | |||
< | |||
<br> | <br> | ||
'''Note:'''<br> | '''Note:'''<br> |
Revision as of 16:32, 9 February 2020
Introduction
UUU (Universal Update Utility) is an open source utility by NXP that allows downloading and executing code on i.MX SoCs through the Serial Download Protocol (SDP).
It is the next generation of NXP's MFGTOOL used to load SPL and U-Boot via the USB OTG port and optionally program the internal storage of the SOM.
For more details please visit https://github.com/NXPmicro/mfgtools
Note:
All Variscite SOMs are shipped with U-Boot pre-programmed on the internal storage.
In addition, all Variscite carrier boards have an SD card slot, and even in the unlikely event of the U-Boot being erased from the internal storage, the SOM can always be booted from an SD card (like our recovery SD card, for example).
So, generally, this utility is not needed, however, it is yet another option that can be used to boot (and optionally program) the Variscite SOMs, for anyone who is interested.
Step by step usage instructions
Download and build uuu:
$ sudo apt-get install libusb-1.0-0-dev libzip-dev libbz2-dev pkg-config cmake $ cd ~ $ git clone https://github.com/NXPmicro/mfgtools.git $ cd mfgtools $ cmake . $ make
Build U-Boot:
- Build U-Boot using the defconfig for SD card/eMMC. You can follow the "Build U-Boot from source code" instructions here.
- Copy the U-Boot image to the uuu directory:
$ cp -v imx-boot-sd.bin ~/mfgtools/uuu $ cd ~/mfgtools/uuu $ ln -fs imx-boot-sd.bin _flash.bin
Boot the board into serial download mode:
- Set the board boot mode to SD card, while not having an actual card inserted in its slot.
Alternatively, set the board boot mode to eMMC/NAND flash, when the eMMC/NAND flash does not contain a bootloader.
Connect the board to your host PC via the USB OTG port, and power on the board.
The board should be recognized on the host as a "NXP Semiconductors SE Blank M850" (or something similar).
Note:
If your board only has a regular USB type-A connector and doesn't have a USB Micro-AB or Type-C receptacle, you can use a "male USB type-A to male USB type-A" cable
Run uuu to load U-Boot on the board:
$ sudo ./uuu ./spl_boot.lst
The board should now run U-Boot.
You can see its output on the console via the debug port, as always.
Note:
The default boot command when booting from USB is bootcmd_mfg. It is defined in the board's default environment.
By default it runs fastboot but can be redefined or made empty.