Yocto Build U-Boot: Difference between revisions
From Variscite Wiki
No edit summary |
No edit summary |
||
| Line 48: | Line 48: | ||
$ cd imx-boot-tools | $ cd imx-boot-tools | ||
{{#ifeq: {{#var:SOC}} | imx8qxp | | |||
# Download SC firmware | |||
$ git clone {{#var:META_VARISCITE_GIT}} -b {{#var:META_VARISCITE_BRANCH}} | |||
$ cp meta-variscite-imx/recipes-bsp/imx-sc-firmware/imx-sc-firmware/mx8qx-var-som-scfw-tcm.bin . | |||
| | |||
# Download DDR and HDMI firmware | # Download DDR and HDMI firmware | ||
$ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin | $ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin | ||
| Line 54: | Line 59: | ||
$ cp {{#var:NXP_FIRMWARE}}/firmware/ddr/synopsys/lpddr4_pmu_train_* . | $ cp {{#var:NXP_FIRMWARE}}/firmware/ddr/synopsys/lpddr4_pmu_train_* . | ||
$ cp {{#var:NXP_FIRMWARE}}/firmware/hdmi/cadence/signed_* . | $ cp {{#var:NXP_FIRMWARE}}/firmware/hdmi/cadence/signed_* . | ||
}} | |||
# Download imx_mkimage | # Download imx_mkimage | ||
$ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}} | $ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}} | ||
| Line 62: | Line 67: | ||
# Download and build ATF | # Download and build ATF | ||
$ git clone {{#var:NXP_IMX_GIT}}/imx-atf -b {{#var:NXP_IMX_BRANCH}} | $ git clone {{#var:NXP_IMX_GIT}}/imx-atf -b {{#var:NXP_IMX_BRANCH}} | ||
$ git clone {{#var:META_VARISCITE_GIT}} -b {{#var:META_VARISCITE_BRANCH}} | {{#ifeq: {{#var:SOC}} | imx8mm | $ git clone {{#var:META_VARISCITE_GIT}} -b {{#var:META_VARISCITE_BRANCH}}|}} | ||
$ cd imx-atf | $ cd imx-atf | ||
$ source {{#var:TOOLCHAIN_LOCATION}} | $ source {{#var:TOOLCHAIN_LOCATION}} | ||
$ export LDFLAGS= | $ export LDFLAGS= | ||
$ git apply ../meta-variscite-imx/recipes-bsp/imx-atf/imx-atf/* | {{#ifeq: {{#var:SOC}} | imx8mm | $ git apply ../meta-variscite-imx/recipes-bsp/imx-atf/imx-atf/*|}} | ||
$ make PLAT={{#var:IMX_ATF_PLAT}} bl31 | $ make PLAT={{#var:IMX_ATF_PLAT}} bl31 | ||
$ cp build/{{#var:IMX_ATF_PLAT}}/release/bl31.bin .. | $ cp build/{{#var:IMX_ATF_PLAT}}/release/bl31.bin .. | ||
| Line 80: | Line 85: | ||
# Build boot image | # Build boot image | ||
$ make -f soc.mak clean | $ make -f soc.mak clean | ||
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} dtbs={{#var:DEFAULT_DTB}} PAD_IMAGE=./pad_image.sh CC=gcc OUTIMG={{#var:U-BOOT_SD_IMAGE_NAME}} flash_evk | $ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} dtbs={{#var:DEFAULT_DTB}} PAD_IMAGE=./pad_image.sh CC=gcc OUTIMG={{#var:U-BOOT_SD_IMAGE_NAME}} {{#ifeq: {{#var:SOC}} | imx8qxp |flash | flash_evk}} | ||
}} | }} | ||
| Line 87: | Line 92: | ||
{{#ifeq: {{#var:SOC_SERIES}} | imx8 | | {{#ifeq: {{#var:SOC_SERIES}} | imx8 | | ||
<br> | <br> | ||
$ sudo dd if={{#var:U-BOOT_SD_IMAGE_NAME}} of=/dev/sdX bs=1K seek= | $ sudo dd if={{#var:U-BOOT_SD_IMAGE_NAME}} of=/dev/sdX bs=1K seek={{#var:U-BOOT_OFFSET}} conv=fsync | ||
| | | | ||
{{#ifeq: {{#var:SPL_SD_IMAGE_NAME}} | N/A | {{#ifeq: {{#var:SPL_SD_IMAGE_NAME}} | N/A | ||
Revision as of 10:38, 20 June 2019
Yocto Build U-Boot from source code
Toolchain installation for out of Yocto builds
To install the toolchain, follow Yocto Toolchain installation.
Build U-Boot out of Yocto tree
Obtain sources:
$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03 $ cd uboot-imx
Configure compilation environment:
$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi
Cleanup everything:
$ make mrproper
Select one of the following configurations:
For booting from SD card/eMMC: $ make mx6var_som_sd_defconfig For booting from NAND flash: $ make mx6var_som_nand_defconfig
Build U-Boot:
$ make -j4
Install the built U-Boot on an SD card
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync $ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync (Replace /dev/sdX with the correct device)
If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:
$ sudo cp SPL /media/rootfs/opt/images/... $ sudo cp u-boot.img /media/rootfs/opt/images/...
And eject the SD card gracefully from host machine.
Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)
Update your U-Boot out of Yocto tree
$ git pull