DART-MX8M CSI: Difference between revisions
No edit summary |
No edit summary |
||
| Line 2: | Line 2: | ||
--> {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | --> {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | ||
--> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_SUMO_V1.0_DART-MX8M}}}} <!-- | --> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_SUMO_V1.0_DART-MX8M}}}} <!-- | ||
--> {{PageHeader|{{#var:HARDWARE_NAME}} Camera}} {{DocImage|category1=Yocto|category2= | --> {{PageHeader|{{#var:HARDWARE_NAME}} Camera}} {{DocImage|category1=Yocto|category2={{#var:HARDWARE_NAME}}}} __toc__ | ||
= Testing MIPI-CSI2 cameras = | = Testing MIPI-CSI2 cameras = | ||
Revision as of 16:14, 2 September 2019
Testing MIPI-CSI2 cameras
Before running any of the pipelines below make sure you have camera(s) connected. i.MX family of processors uses gstreamer as multimedia framework. Please refer to https://gstreamer.freedesktop.org/
Camera Probe
Run the following command to see if you have the camera(s) detected
# v4l2-ctl --list-devices
This should produce the following output
# v4l2-ctl --list-devices
i.MX6S_CSI (platform:30a90000.csi1_bridge):
/dev/video0
i.MX6S_CSI (platform:30b80000.csi2_bridge):
/dev/video1
As you can see above there are 2 cameras accessible as /dev/video0 and /dev/video1
Testing Camera Preview on Display
In the examples below /dev/videoX is either /dev/video0 or /dev/video1
- 480P 640x480@30fps:
# gst-launch-1.0 v4l2src device=/dev/videoX ! video/x-raw,width=640,height=480 ! autovideosink
- NTSC 720x480@30fps:
# gst-launch-1.0 v4l2src device=/dev/videoX ! video/x-raw,width=720,height=480 ! autovideosink
- 720P 1280x720@30fps:
# gst-launch-1.0 v4l2src device=/dev/videoX ! video/x-raw,width=1280,height=720 ! autovideosink
- 1080P: 1920x1080@30fps:
# gst-launch-1.0 v4l2src device=/dev/videoX ! video/x-raw,width=1920,height=1080 ! autovideosink
- QSXGA 2592x1944@15fps:
# gst-launch-1.0 v4l2src device=/dev/videoX ! video/x-raw,width=2592,height=1944 ! autovideosink
Testing Camera JPEG Snapshot
To capture JPEG snapshot run one of the pipelines below depending upon the required picture resolution.
In the examples below /dev/videoX is either /dev/video0 or /dev/video1
- 480P 640x480:
# gst-launch-1.0 v4l2src device=/dev/videoX num-buffers=1 ! video/x-raw,width=640,height=480 ! jpegenc ! filesink location=/tmp/test.jpg
- NTSC 720x480:
# gst-launch-1.0 v4l2src device=/dev/videoX num-buffers=1 ! video/x-raw,width=720,height=480 ! jpegenc ! filesink location=/tmp/test.jpg
- 720P 1280x720:
# gst-launch-1.0 v4l2src device=/dev/videoX num-buffers=1 ! video/x-raw,width=1280,height=720 ! jpegenc ! filesink location=/tmp/test.jpg
- 1080P 1920x1080:
# gst-launch-1.0 v4l2src device=/dev/videoX num-buffers=1 ! video/x-raw,width=1920,height=1080 ! jpegenc ! filesink location=/tmp/test.jpg
- QSXGA 2592x1944:
# gst-launch-1.0 v4l2src device=/dev/videoX num-buffers=1 ! video/x-raw,width=2592,height=1944 ! jpegenc ! filesink location=/tmp/test.jpg
Using both cameras simultaneously
The following pipeline is an example of using both cameras simultaneously.
In this example a short video stream from each camera is saved as an MJPEG-encoded AVI file.
# gst-launch-1.0 v4l2src device=/dev/video0 num-buffers=100 ! video/x-raw,width=1920,height=1080 ! jpegenc ! avimux ! filesink location=./test0.avi \
v4l2src device=/dev/video1 num-buffers=100 ! video/x-raw,width=1920,height=1080 ! jpegenc ! avimux ! filesink location=./test1.avi