Latest revision as of 09:18, 18 April 2016

VAR-SOM-MX6 - NAND Flash Burning

Introduction

The Variscite VAR-SOM-MX6 / VAR-SOM-SOLO SOMs use the on-SOM NAND-Flash to boot.
The file system can reside either on the NAND-Flash or the eMMC.
When file system resides on NAND, UBIFS file system will be used.
When file system resides on eMMC, EXT3 file system will be used.
Regardless if the file system is on NAND/UBIFS or eMMC/EXT3 the u-boot will always boot from NAND. The only exception is the VAR-DART-MX6, where boot is from eMMC completely.

NOTE:
This WIKI is only valid for VAR-SOM-MX6, VAR-SOM-SOLO/DUAL. For DART-MX6 please use: NAND Flash Burning Dart

NAND Structure

When system boots, kernel logs will present 4 relevant partitions defined.
0x000000000000-0x000000200000 : "spl"
0x000000200000-0x000000400000 : "bootloader"
0x000000400000-0x000000a00000 : "kernel"
0x000000a00000-0x000040000000 : "rootfs"

Yocto Built binaries for NAND-Flash

The resulted images are locaated in tmp/deploy/images/var-som-mx6.
Looking at tmp/deploy/images/var-som-mx6 you will find 5 required files for a complete NAND-Flash based system that are linked to the actual file:
SPL,U-Boot, zImage, <dtb file>, fsl-image-qt5-minimal-var-som-mx6.ubi

Image Name	How to use
fsl-image-qt5-minimal-var-som-mx6.ubi	A complete UBIFS file-system binary. ("rootfs")
uImage	Linux kernel image ("kernel")
SPL-nand	The SPL is pre-u-boot SW component, required for DDR intialization ("spl")
u-boot-nand-2014.04-r0.img	u-boot built for nand ("bootloader")
Device Tree Name (Choose only one, according to your SOM and carrier board	SOM type	Carrier Board type	LCD Type	Evaluation Kit name
uImage-imx6q-var-som.dtb	VAR-SOM-MX6_V2 (Quad / Dual)	VAR-MX6CustomBoard	Capacitive/Resistive touch	VAR-DVK-MX6_V2-PRO VAR-STK-MX6_V2
uImage-imx6q-var-som-vsc.dtb	VAR-SOM-MX6_V2 (Quad / Dual)	VAR-SOLOCustomBoard	Capacitive LVDS touch	N/A
uImage-imx6dl-var-som.dtb	VAR-SOM-MX6_V2 (DualLite/ Solo)	VAR-MX6CustomBoard	Capacitive/Resistive touch	N/A
uImage-imx6dl-var-som-solo-vsc.dtb	VAR-SOM-SOLO / VAR-SOM-DUAL	VAR-SOLOCustomBoard	Capacitive LVDS touch	VAR-DVK-SOLO/DUAL VAR-STK-SOLO/DUAL
uImage-imx6dl-var-som-solo.dtb	VAR-SOM-SOLO / VAR-SOM-DUAL	VAR-MX6CustomBoard	Capacitive/Resistive touch	N/A
uImage-imx6q-var-dart.dtb	VAR-SOM-SOLO / VAR-SOM-DUAL	VAR-DT6CustomBoard	Capacitive LVDS touch	VAR-STK-DT6.VAR-DVK-DT6

NAND Flashing scripts

If you followed Create an extended SD-Card the NAND flashing scripts will be included in your SD-Card.
The NAND flashing scripts are easy-to-use example scripts for burning images into NAND Flash

NAND-Flash images locations

The below directory stucture on your SD-Card, elaborates the files' location which the below burning scripts are expecting

/media/rootfs/opt/images/
├── Android
│   └── Emmc
│       ├── boot.img
│       ├── boot-imx6q-var-dart.img
│       ├── boot-som-mx6dl-c.img
│       ├── boot-som-mx6dl-r.img
│       ├── boot-som-mx6q-c.img
│       ├── boot-som-mx6q-r.img
│       ├── boot-som-mx6q-vsc.img
│       ├── boot-som-solo-c.img
│       ├── boot-som-solo-r.img
│       ├── boot-som-solo-vsc.img
│       ├── recovery.img
│       ├── recovery-imx6q-var-dart.img
│       ├── recovery-som-mx6dl-c.img
│       ├── recovery-som-mx6dl-r.img
│       ├── recovery-som-mx6q-c.img
│       ├── recovery-som-mx6q-r.img
│       ├── recovery-som-mx6q-vsc.img
│       ├── recovery-som-solo-c.img
│       ├── recovery-som-solo-r.img
│       ├── recovery-som-solo-vsc.img
│       ├── SPL
│       ├── SPL.mmc
│       ├── SPL.new
│       ├── system.img
│       ├── u-boot-var-imx6-nand.img
│       └── u-boot-var-imx6-sd.img
└── Yocto
    ├── rootfs.tar.bz2
    ├── rootfs.ubi.img
    ├── SPL
    ├── SPL.mmc
    ├── u-boot.img
    ├── u-boot.img.mmc
    ├── uImage
    ├── uImage-imx6dl-var-som.dtb
    ├── uImage-imx6dl-var-som-solo.dtb
    ├── uImage-imx6dl-var-som-solo-vsc.dtb
    ├── uImage-imx6q-var-dart.dtb
    ├── uImage-imx6q-var-som.dtb
    └── uImage-imx6q-var-som-vsc.dtb

Prepare images for NAND-Flash / eMMC burning

Plug the bootable SDCARD into your host machine. Then your host machine should mount the rootfs partition on /media/rootfs.
Copy all yocto-built binaries into SD-Card:

Note: If you followed Create an extended SD-Card the NAND-Flash flashing scripts and all relevant binaries are already included in your SD-Card! and below commands are redundant

$ export YOCTO_ROOT=~/var-som-mx6-yocto-fido

Linux:
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage /media/rootfs/opt/images/Yocto
U-boot:
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/SPL-nand /media/rootfs/opt/images/Yocto/SPL
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/u-boot-nand-2014.04-r0.img /media/rootfs/opt/images/Yocto/u-boot.img
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/SPL-sd /media/rootfs/opt/images/Yocto/SPL.mmc
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/u-boot-sd-2014.04-r0.img /media/rootfs/opt/images/Yocto/u-boot.img.mmc
File System:
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/fsl-image-qt5-var-som-mx6.tar.bz2 /media/rootfs/opt/images/Yocto/rootfs.tar.bz2
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/fsl-image-qt5-minimal-var-som-mx6.ubi /media/rootfs/opt/images/Yocto/rootfs.ubi.img
Device Tree:
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6dl-var-som-solo.dtb /media/rootfs/opt/images/Yocto/
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6dl-var-som-solo-vsc.dtb /media/rootfs/opt/images/Yocto/
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6dl-var-som.dtb /media/rootfs/opt/images/Yocto/
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6q-var-som.dtb /media/rootfs/opt/images/Yocto/
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6q-var-som-vsc.dtb /media/rootfs/opt/images/Yocto/
$ sudo cp ${YOCTO_ROOT}/build_x11/tmp/deploy/images/var-som-mx6/uImage-imx6q-var-dart.dtb /media/rootfs/opt/images/Yocto/

NAND-Flash Flashing scripts

The flashing scripts are located at /media/rootfs/sbin/

 
$ android-emmc.sh - flash Android into eMMC
$ yocto-emmc.sh - flash Yocto into eMMC (See note below)
$ yocto-dart.sh - flash Yocto into eMMC DART only.
$ yocto-nand.sh - flash Yocto into nand

in case of yocto-emmc.sh, change boot arguments to :

$ setenv bootargs console=ttymxc0,115200 video=mxcfb1:off root=/dev/mmcblk1p1 rootwait rw
$ saveenv

Manual step-by-step flashing to NAND

Flash U-BOOT

Flashing U-BOOT reguire to flash 2 parts: SPL and u-boot.img. Assume you copy SPL-nand and u-boot-nand-2014.04-r0.img to the right directory as showed above.

$ cd /opt/images/Yocto
$ flash_erase /dev/mtd0 0 0
$ kobs-ng init -x SPL --search_exponent=1 -v
$ flash_erase /dev/mtd1  0 0
$ nandwrite -p /dev/mtd1 u-boot.img

Flash Linux Kernel

Flashing Linux kernel reguire to flash 2 parts: uImage and device tree. Assume you copy uImage and device tree to the right directory as showed above. You also need to pick and coose the right DTB file. See table above for a complete description.

$ cd /opt/images/Yocto
$ flash_erase /dev/mtd2 0 0
$ nandwrite -p /dev/mtd2 uImage
$ nandwrite -p /dev/mtd1 -s 0x1e0000 uImage-imx6q-var-som.dtb (Example, select the right one!)

Flash UBIFS

The parameters for the UBIFS UBI_SUB_PAGE_SIZE=2048 and UBI_VID_HDR_OFFSET=2048.

$ cd /opt/images/Yocto
$ flash_erase /dev/mtd3 0 0
$ ubiformat /dev/mtd3 -f rootfs.ubi.img -s 2048 -O 2048

Flash File System to eMMC

Flashing eMMC is a complex task. It requires several steps including partition, format and untar the file system. We highly recommend to use our provided scripts to perform this task. Assuming that you use our NAND recovery utility.

Make sure the eMMC is not mounted.

$ cd /opt/images/Yocto
$ umount /dev/mmcblk1p*
$ node=/dev/mmcblk1

Delete all partition from the eMMC.

$ fdisk ${node} <<EOF
d
1
d
2
d
3
d
w
EOF

$ sync

Delete MBR

$ dd if=/dev/zero of=${node} bs=512 count=1000
$ sync

Call sfdisk to create partition table

$ node=/dev/mmcblk1
$ seprate=40
$ total_size=`sfdisk -s ${node}`
$ total_size=`expr ${total_size} / 1024`

$ sfdisk --force -uM ${node} << EOF
,${total_size},83
EOF

Format Linux

$ mkfs.ext4 ${node} -Lrootfs

Flash Linux

$ mkdir /run/media/mmcblk1p1
$ mount ${node}  /run/media/mmcblk1p1
$ tar xvpf rootfs.tar.bz2 -C /run/media/mmcblk1p1/

in case of Yocto eMMC file system stop at u-boot and change boot arguments to :

$ setenv bootargs console=ttymxc0,115200 video=mxcfb1:off root=/dev/mmcblk1p1 rootwait rw
$ saveenv

Summary

We describe the results of Yocto build, how to copy it to SDCARD and how to flash it to NAND and eMMC. This page is not valid for DART-MX6. Please follow the link to the relevant page. With the NAND recovery utility we provide a set of scripts located on /sbin and listed below. It is much safer to use them instead of the manual operation.
/media/rootfs/sbin/:
android-emmc.sh mkmmc_yocto.sh yocto-dart.sh yocto-nand.sh mkmmc_android.sh nand-recovery.sh yocto-emmc.sh. Some of the scripts are used by the others.
Please use:

android-emmc.sh to flash Android int eMMC
yocto-dart.sh To flash Yocto into eMMC on DART-MX6
yocto-nand.sh To flash Yocto into NAND (not relevant on DART-MX6)
yocto-emmc.sh To flash Yocto into eMMC (not relevant on DART-MX6)

@@ Line 1: / Line 1: @@
 {{PageHeader|VAR-SOM-MX6 - NAND Flash Burning}} {{DocImage|category1=VAR-SOM-MX6|category2=Yocto}} __toc__
 = Introduction =
-Variscite SOM uses the on-SOM NAND Flash to boot.<br>
+The Variscite VAR-SOM-MX6 / VAR-SOM-SOLO SOMs use the on-SOM NAND-Flash to boot.<br>
-The file system can reside either on the NAND or the eMMC.
+The file system can reside either on the NAND-Flash or the eMMC.
 <br>When file system resides on NAND, UBIFS file system will be used.
 <br>When file system resides on eMMC, EXT3 file system will be used.
@@ Line 27: / Line 27: @@
 |-
 | fsl-image-qt5-minimal-var-som-mx6.ubi
-| A complete UBIFS file-system binary.
+| A complete UBIFS file-system binary. ("rootfs")
 |-
 | uImage
-| Linux kernel image
+| Linux kernel image ("kernel")
 |-
 | SPL-nand
-| The SPL is pre-u-boot SW component, required for DDR intialization
+| The SPL is pre-u-boot SW component, required for DDR intialization ("spl")
 |-
 | u-boot-nand-2014.04-r0.img
-| u-boot built for nand
+| u-boot built for nand ("bootloader")
 |-
 ! scope="col" | Device Tree Name <br>(Choose only one, according to your SOM and carrier board<br/>
@@ Line 82: / Line 82: @@
 |}
-== NAND recovery scripts==
+== NAND Flashing scripts==
-The NAND recovery scripts are for burning images into NAND Flash<br>
-Features:
-* The utility is a part of the Bootable SD-Card provided by Variscite. So it can be used on any platform type.
-* Flash Yocto u-boot and kernel onto NAND, file system onto EXT3/eMMC (Where available)
-* Flash Yocto u-boot and kernel onto NAND, file system onto UBIFS/NAND
-* Flash Android u-boot onto NAND, boot image and system image onto eMMC
-=== NAND recovery SDCARD partition ===
+If you followed [[VAR-SOM-MX6 Yocto Fido R3 Build Yocto release#Create_an_extended_SD-Card |Create an extended SD-Card]] the  [[VAR-SOM-MX6 NAND Flash Burning#NAND-Flash Flashing scripts |NAND flashing scripts]] will be included in your SD-Card. <br>
-Directly raw flashed onto the SCDARD are the SPL and u-boot.
+The [[VAR-SOM-MX6 NAND Flash Burning#NAND-Flash Flashing scripts |NAND flashing scripts]] are easy-to-use example scripts for burning images into NAND Flash<br>
-The first partition is the boot partition. It contains all device trees and kernel uImage.
-<br/>/media/BOT_VAR_SOM/
-<br/>uImage
-<br/>imx6dl-var-som.dtb
-<br/>imx6dl-var-som-solo-vsc.dtb
-<br/>imx6q-var-som.dtb
-<br/>imx6dl-var-som-solo.dtb
-<br/>imx6q-var-dart.dtb
-<br/>imx6q-var-som-vsc.dtb
-<br/>The second partition is called rootfs. It is a complete Linux file system.
-=== NAND recovery boot logic ===
-The u-boot running from SDCARD scan the hardware and set various environment variables. This will automatically identify the platform and boot correctly.
-<br/>Variables:
-* screen_alternate=yes - System has a capacitive display otherwise resistive display.
-* var_auto_fdt_file=Y - Automatically set the environment variables. N disable it.
-* fdt_file= - one of the above device tree file.
-{{note| NOTE:<br>This mechanism is not available on NAND. We identify the hardware in the flashing scripts and flash the relevant device tree onto NAND.|info}}
-=== NAND recovery images locations ===
+=== NAND-Flash images locations ===
-We copy the image files into the NAND recovery utility. We also change the names of the products above.
+The below directory stucture on your SD-Card, elaborates the files' location which the below burning scripts are expecting
-The NAND recovery utlity contains Android and Yocto.
 <pre>
 /media/rootfs/opt/images/
@@ Line 160: / Line 136: @@
 </pre>
-=== NAND recovery scripts ===
+== Prepare images for NAND-Flash / eMMC burning ==
-<pre>
+Plug the bootable SDCARD into your host machine.
-Script files located on /media/rootfs/sbin/
+Then your host machine should mount the rootfs partition on /media/rootfs.<br>
-android-emmc.sh
+Copy all yocto-built binaries into SD-Card:
-mkmmc_yocto.sh
+<br>
-yocto-dart.sh
+* <span style="color:red">Note:</span> If you followed [[VAR-SOM-MX6 Yocto Fido R3 Build Yocto release#Create_an_extended_SD-Card |Create an extended SD-Card]] the  [[VAR-SOM-MX6_NAND Flash Burning#NAND-Flash Flashing scripts| NAND-Flash flashing scripts]] and all relevant binaries are already included in your SD-Card! and below commands are redundant<br>
-yocto-nand.sh
-mkmmc_android.sh
-nand-recovery.sh
-yocto-emmc.sh
-</pre>
-== Copy Yocto files into SDCARD ==
-Plug the NAND recovery SDCARD into your host machine.
-Then your host machine should mount the rootfs partition on /media/rootfs.
 <pre>
 $ export YOCTO_ROOT=~/var-som-mx6-yocto-fido
@@ Line 197: / Line 165: @@
 </pre>
-== Flashing to NAND ==
+== NAND-Flash Flashing scripts ==
+The flashing scripts are located at /media/rootfs/sbin/
+<pre>
+$ android-emmc.sh - flash Android into eMMC
+$ yocto-emmc.sh - flash Yocto into eMMC (See note below)
+$ yocto-dart.sh - flash Yocto into eMMC DART only.
+$ yocto-nand.sh - flash Yocto into nand
+</pre>
+* in case of yocto-emmc.sh, change boot arguments to : <br>
+<pre>
+$ setenv bootargs console=ttymxc0,115200 video=mxcfb1:off root=/dev/mmcblk1p1 rootwait rw
+$ saveenv
+</pre>
+== Manual step-by-step flashing to NAND ==
 === Flash U-BOOT ===
 Flashing U-BOOT reguire to flash 2 parts: SPL and u-boot.img.
@@ Line 216: / Line 198: @@
 $ flash_erase /dev/mtd2 0 0
 $ nandwrite -p /dev/mtd2 uImage
-$ nandwrite -p /dev/mtd1 -s 0x1e0000 uImage-imx6q-var-som.dtb (Example select the right one!)
+$ nandwrite -p /dev/mtd1 -s 0x1e0000 uImage-imx6q-var-som.dtb (Example, select the right one!)
 </pre>
 === Flash UBIFS ===
 The parameters for the UBIFS UBI_SUB_PAGE_SIZE=2048 and UBI_VID_HDR_OFFSET=2048.

VAR-SOM-MX6 NAND Flash Burning: Difference between revisions