DART-MX8M suspend: Difference between revisions
No edit summary |
No edit summary |
||
| (8 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
<!-- Set release according to "release" parameter in URL and use RELEASE_SUMO_V1.0_DART-MX8M as default | <!-- Set release according to "release" parameter in URL and use RELEASE_SUMO_V1.0_DART-MX8M as default | ||
--> {{# | --> {{INIT_RELEASE_PARAM|RELEASE_SUMO_V1.0_DART-MX8M}}<!--- | ||
--> {{#lst: | --> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM}}}} <!-- | ||
--> {{#lst:B2QT_Platform_Customization|{{#var:RELEASE_PARAM}}}} <!-- | |||
--> {{#lst:Debian_Platform_Customization|{{#var:RELEASE_PARAM}}}} <!-- | |||
--> {{PageHeader|{{#var:HARDWARE_NAME}} Suspend to RAM}}{{DocImage|category1=Yocto|category2=Debian}}[[Category:DART-MX8M]][[Category:DART-MX8M-MINI]][[Category:DART-MX8M-PLUS]] | --> {{PageHeader|{{#var:HARDWARE_NAME}} Suspend to RAM}}{{DocImage|category1=Yocto|category2=Debian}}[[Category:DART-MX8M]][[Category:DART-MX8M-MINI]][[Category:DART-MX8M-PLUS]] | ||
= Suspend to RAM = | = Suspend to RAM = | ||
| Line 51: | Line 53: | ||
= Measuring SOM current consumption in suspend = | = Measuring SOM current consumption in suspend = | ||
To measure SOM current consumption remove resistor R15 and connect | To measure the SOM current consumption remove resistor R15 on DT8MCustomBoard or R58 on Symphony-Board and connect an ammeter in its place.<br> | ||
It is recommended to boot from eMMC to get accurate measurement. | It is recommended to boot from eMMC to get an accurate measurement. | ||
{{#ifeq: {{#var:HARDWARE_NAME}}|DART-MX8M|| | {{#ifeq: {{#var:HARDWARE_NAME}}|DART-MX8M|| | ||
{{Note|To achieve minimum power consumption during suspend it is necessary to remove two resistors on the Symphony-Board related to the Ethernet jack LEDs – R79 and R80.<br> | {{Note|To achieve minimum power consumption during suspend it is necessary to remove two resistors on the Symphony-Board related to the Ethernet jack LEDs – R79 and R80.<br> | ||
If assembled they back-feed the BASE_3V3 into the non-powered Ethernet PHY during suspend, increasing power consumption.}}} | If assembled they back-feed the BASE_3V3 into the non-powered Ethernet PHY during suspend, increasing power consumption.}}}} | ||
Latest revision as of 22:08, 25 October 2024
This page is using the default release RELEASE_SUMO_V1.0_DART-MX8M.
To view this page for a specific Variscite SoM and software release, please follow these steps:
- Visit variwiki.com
- Select your SoM
- Select the software release
Suspend to RAM
This state offers significant power savings as everything in the system is put into a low-power state, except for memory, which is placed into the self-refresh mode to retain its contents.
To suspend to RAM execute the following command:
# pm-suspend
Wake up
There are many possible ways to wake up from suspend.
A few examples:
- Pushing the ON/OFF button (when present on the board)
- Pushing a button on the board which has the boolean property "wakeup-source" set in its device tree node (under gpio_keys), e.g.:
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_keys>;
...
back {
label = "Back";
gpios = <&gpio4 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_BACK>;
wakeup-source;
};
};
- Pressing the capacitive touch which has the "wakeup-source" property set in its device tree node, e.g.:
ft5x06_ts: ft5x06_ts@38 {
status = "disabled";
compatible = "edt,edt-ft5x06";
reg = <0x38>;
reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_touch>;
interrupt-parent = <&gpio1>;
interrupts = <14 0>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
wakeup-source;
};
Measuring SOM current consumption in suspend
To measure the SOM current consumption remove resistor R15 on DT8MCustomBoard or R58 on Symphony-Board and connect an ammeter in its place.
It is recommended to boot from eMMC to get an accurate measurement.