YPC VAR-SOM-MX8: Difference between revisions

Revision as of 07:39, 25 June 2022

sumo-fsl-4.14.98-mx8-v1.1

sumo-fsl-4.14.98-mx8-v1.2

sumo-fsl-4.14.98-mx8-v1.3

sumo-fsl-4.14.98-mx8-v1.4

sumo-fsl-4.14.98-mx8-v1.5

sumo-fsl-4.14.98-mx8-v1.6

sumo-fsl-4.14.98-mx8-v1.7

sumo-fsl-4.14.98-mx8-v1.8

sumo-fsl-4.14.98-mx8-v1.9

zeus-fsl-5.4.3-mx8-v1.0

zeus-fsl-5.4.3-mx8-v1.1

zeus-fsl-5.4.3-mx8-v1.2

dunfell-fslc-5.4-2.1.x-mx8-v1.0

dunfell-fslc-5.4-2.1.x-mx8-v1.1

dunfell-fslc-5.4-2.1.x-mx8-v1.2

dunfell-fslc-5.4-2.1.x-mx8-v1.3

dunfell-fslc-5.4-2.1.x-mx8-v1.4

dunfell-fslc-5.4-2.1.x-mx8-v1.5

mx8-yocto-hardknott-5.10.72_2.2.1-v1.0

mx8-yocto-hardknott-5.10.72_2.2.1-v1.1

-->

@@ Line 1,745: / Line 1,745: @@
 -->{{#vardefine:META_VARISCITE_COMMIT|5d0c9fbea1751971b599f78d6e98449835a65d98}} <!--
 -->{{#vardefine:RELEASE_DATE|06/24/2022}} <section end=mx8-yocto-hardknott-5.10.72_2.2.1-v1.1/>
---><section begin=RN_mx8-yocto-hardknott-5.10.72_2.2.1-v1.1/>
-|-
-| <span {{#var:STYLE_RELEASE}}>Release 1.1</span> ||
-|-
-| U-Boot: fec2: aligned to fec1 for consistency ||
-|-
-| U-Boot: fec1: tune phy-reset-post-delay with proper value ||
-|-
-| U-Boot: ethphy1: remove no need rx-internal-delay-ps property ||
-|-
-| Linux: ethphy1: remove no need rx-internal-delay-ps property ||
-|-
-| Linux: ptn5150: use interrupts instead of deprecated int-gpio ||
-|-
-| Linux: extcon: ptn5150: Add irq-is-id-quirk ||
-|-
-| Linux: imx-lpi2c: change log level for eDMA related logs ||
-|-
-| Linux: ptn5150: enable irq-is-id-quirk || irq-is-id-quirk allows the id pin to be used as an interrupt to avoid using a separate device tree file for Symphony <= 1.4.
-|-
-| meta-layer: libubootenv: link with bfd instead of gold ||
-|-
-| meta-layer: linux-variscite: Remove KERNEL_CONFIG_COMMAND ||
-|-
-| <span {{#var:STYLE_RELEASE}}>Release 1.0</span> ||
-|-
-| Initial Yocto Hardknott release based on NXP lf-5.10.72_2.2.1 || (kernel 5.10.72)
-|-
-! Known Issues !!
-|-
-| RPMSG Demos from U-Boot || Starting from BSP 5.10.72 NXP stopped supporting Cortex-m firmwares loaded from U-Boot
-|-
-| HDMI and DP suspend/resume crash || Using HDMI or DP display, resume from suspend ends up in a kernel crash
-|-
-| USB Type-A ports are not supported in U-Boot on SPEAR-MX8 || U-Boot USB driver does not recognize USB devices behind the hub
-|-
-| USB Type-A ports don't work after resume from suspend in Linux on SPEAR-MX8 || USB driver does not recognize USB devices behind the hub
-|}
-{{#vardefine:CHANGE_LOG_FOUND|true}}
-<section end=RN_mx8-yocto-hardknott-5.10.72_2.2.1-v1.1/>