Yocto Build U-Boot: Difference between revisions
From Variscite Wiki
(Skip ATF patches if VARISCITE_ATF_GIT set) |
(Remove empty space) |
||
| Line 121: | Line 121: | ||
{{#ifeq: {{#var:SOC}}|mx8mp| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | | {{#ifeq: {{#var:SOC}}|mx8mp| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/* | | ||
{{#ifeq: {{#var:SOC}}|mx8mm| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8mm* ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-* | | {{#ifeq: {{#var:SOC}}|mx8mm| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8mm* ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-* | | ||
{{#ifeq: {{#var:SOC}}|mx8mq| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-*|}} }} }} }} }} }} | {{#ifeq: {{#var:SOC}}|mx8mq| $ git apply ../{{#var:META_VARISCITE_REPO}}/recipes-bsp/imx-atf/imx-atf/imx8m-*|}} }} }} }} }} }} }} | ||
$ source {{#var:TOOLCHAIN_LOCATION}} | $ source {{#var:TOOLCHAIN_LOCATION}} | ||
$ unset LDFLAGS | $ unset LDFLAGS | ||
Revision as of 21:28, 17 November 2020
Yocto Build U-Boot from source code
Toolchain installation for out of Yocto builds
To install the toolchain, follow Yocto Toolchain installation.
Build U-Boot out of Yocto tree
Obtain sources:
$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03 $ cd uboot-imx
Configure compilation environment:
$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi
Cleanup everything:
$ make mrproper
Select one of the following configurations:
For booting from SD card/eMMC: $ make mx6var_som_sd_defconfig For booting from NAND flash: $ make mx6var_som_nand_defconfig
Build U-Boot:
$ make -j4
Install the built U-Boot on an SD card
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync $ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync (Replace /dev/sdX with the correct device)
If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:
$ sudo cp SPL /media/rootfs/opt/images/... $ sudo cp u-boot.img /media/rootfs/opt/images/...
And eject the SD card gracefully from host machine.
Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)
Update your U-Boot out of Yocto tree
$ git pull