Latest revision as of 22:58, 26 October 2020

DART-SD410 - First Time? Start Here.

This WIKI describes:

Variscite's FTP tree explanatioon.
Switching between Android and Linux.
How to start using your VAR-SD410CustomBoard.

Variscite's FTP

The Variscite's FTP directory tree is as following:

dart-sd410
├── Software
│   ├── Android
│   │   ├── LL.1.2.4-01810-8x16.0-3
│   │   ├── ...
│   │   └── RescueImages
│   ├── Yocto
│   │   ├── ...
│   │   └── RescueImages
│   ├── Ubuntu
│   │   ├── ...
│   │   └── RescueImages
│   ├── Windows
│   │   ├── ...
│   │   └── RescueImages
│   └── EmmcRecovery
└── Hardware
    ├── Schematics
    ├── Datasheets
    └── Layout

dart-sd410 -> Software -> EmmcRecovery directory contains a recovery SD Card image for switching OSes and Recovery
dart-sd410 -> Software -> OS -> RescueImages directory contains prebuilt last version of the system together with partition table file and boot loaders.

NOTE:
Please refer to support@variscite.com for obtaining FTP credentials.

NOTE:

The partition table file and bootloaders are supplied in binary format and cannot be altered by the customers.

Please contact variscite support for changes.

Switching between OSes

Download the Recovery SD Card Image (RecoverySD_rev2.3.zip) from Variscite's FTP site. It is located in dart-sd410 -> Software -> EmmcRecovery directory
Check that the MD5 check sum is exactly the one that is written in RecoverySD_rev2.1.img.md5sum file

$ md5sum RecoverySD_rev2.3.zip

Preparing rescue SD-Card

Extract the image from the archive

$ unzip RecoverySD_rev2.3.zip

Plug your SD card to your Linux machine, run dmesg and see what device is added (i.e. /dev/sdX)
Run the following command to write the image file to the SD card

$ sudo dd if=~/RecoverySD_rev2.3.img of=/dev/sdX bs=128k
Change the /dev/sdX with your SD card device.

After the writing process is finished, run
$ sudo sync

Remove the SD card from your PC and insert it into the SD card slot of the VAR-SD410CustomBoard
Set Boot Select switch (SW3) to the ON position. This directs the DART-SD410 to boot from an external SD card. After this step, the system will read the image from the external SD card and boot into Debian.
Connect VAR-SD410CustomBoard to a PC using the USB cable. Please pay attention to use the Debug USB connector (J21). A new COM port should be found on a PC.
Open any terminal to a newly created com port using 115200,8,n,1 settings.
Power up the board.
Navigate to /media/Linaro/OSes/Android or /media/Linaro/OSes/Debian directory.

# cd /media/linaro/OSes/Android
or
# cd /media/linaro/OSes/Debian

Execute update.sh script.

# ./update.sh

Let the script finish the update process.
Remove the SD
Cycle the power of VAR-SD410CustomBoard.

The needed OS will start

NOTE:
To get the most updated images it is suggested to use fastboot and precompiled images to upgrade to the latest version

NOTE:
There are many error messages occure on DART-SD410 that is coming without Wi-Fi assembled. The Wi-Fi driver should be removed from the SD Card in this case:

# rm /lib/modules/4.9.56-linaro-lt-qcom/kernel/drivers/remoteproc/qcom_wcnss_pil.ko
# reboot

Start using your VAR-SD410CustomBoard

Upack the contents of the package
Veryfy that the DART-SD410 SoM is connected properly into VAR-SD410CustomBoard card
Connect the screen LVDS cable to the LCD (the red wires should be at pin 1 position)
Connect the other side of the cable to VAR-SD410CustomBoard J11 (the red wires should be at pin 1 position i.e. closer to HDMI connector)
Connect the touch screen flat cable to J4 (the copper contacts should face PCB card)
Connect USB cable to a PC
Connect the Micro USB plug to VAR-SD410CustomBoard J21. Wait for USB device enumeration and driver installation
Open any serial port console program (we suggest using Putty) and set it to 115200,8,1,n baudrate
Plug in the power supply to 100/220V

NOTE:
If Camera adapter was purchased then it should be plugged in before the first power up. Otherwise the Android will remove Camera program and it will not be accessible untill system re-flash

Plug in the power adapter 5V to VAR-SD410CustomBoard J18

Immideately the serial console will show the booting process and after about a minute the LCD will show the boot animation and Android will be started

NOTE:
The first Boot up of the Android takes more time because of database initialization

NOTE:
Please remove SD card from the slop before boot

Switching display options in Android

To switch between LCD and HDMI the following fastboot commands should be run

To switch to HDMI

$ fastboot oem select-display-panel adv7533_1080p

To switch to LCD

$ fastboot oem select-display-panel

@@ Line 4: / Line 4: @@
 *Variscite's FTP tree explanatioon.<br/>
 *Switching between Android and Linux.<br/>
-*How to start using your VAR-DT410CustomBoard.<br/>
+*How to start using your VAR-SD410CustomBoard.<br/>
 =Variscite's FTP=
@@ Line 13: / Line 13: @@
 │   ├── Android
 │   │   ├── LL.1.2.4-01810-8x16.0-3
+│   │   ├── ...
 │   │   └── RescueImages
 │   ├── Yocto
+│   │   ├── ...
+│   │   └── RescueImages
 │   ├── Ubuntu
+│   │   ├── ...
+│   │   └── RescueImages
 │   ├── Windows
-│   └── RescueDiskImage
+│   │   ├── ...
+│   │   └── RescueImages
+│   └── EmmcRecovery
 └── Hardware
      ├── Schematics
@@ Line 23: / Line 30: @@
      └── Layout
 </pre>
+* dart-sd410 -> Software -> EmmcRecovery directory contains a recovery SD Card image for switching OSes and Recovery
+* dart-sd410 -> Software -> ''OS'' -> RescueImages directory contains prebuilt last version of the system together with partition table file and boot loaders.
+{{note| NOTE:<br>
+Please refer to support@variscite.com for obtaining FTP credentials.|info}}
+{{note| NOTE:<br>
+The partition table file and bootloaders are supplied in binary format and cannot be altered by the customers.<br>
+Please contact variscite support for changes.|info}}
 = Switching between OSes =
-In this section each supported OS has it's own subdirectory.<br/>
+*Download the Recovery SD Card Image (RecoverySD_rev2.3.zip) from Variscite's FTP site. It is located in dart-sd410 -> Software -> EmmcRecovery directory
-Additional directory named RescueDiskImage holds inside the rescue disk for switching between different OSes.<br/>
+*Check that the MD5 check sum is exactly the one that is written in RecoverySD_rev2.1.img.md5sum file
-The partition table of Android and Linux is different and this image will help update the needed partition table.<br/>
+<pre>
-To use this image it should be burnt into SD Card, to do so please follow:
+$ md5sum RecoverySD_rev2.3.zip
+</pre>
 '''Preparing rescue SD-Card'''<br/>
+*Extract the image from the archive
+<pre>
+$ unzip RecoverySD_rev2.3.zip
+</pre>
 *Plug your SD card to your Linux machine, run dmesg and see what device is added (i.e. /dev/sd<span style="color: rgb(255, 0, 0);">'''X'''</span>)<br/>
-Run the following command to write the image file to the SD card
+*Run the following command to write the image file to the SD card
 <pre>
-$ sudo dd if=~/Downloads/DART-DT410_sd_rescue.img of=/dev/sdX bs=128k
+$ sudo dd if=~/RecoverySD_rev2.3.img of=/dev/sdX bs=128k
-Change the /dev/sdX with your SC card device.
+Change the /dev/sdX with your SD card device.
-After the write process is finished run
+After the writing process is finished, run
 $ sudo sync
 </pre>
-*Remove the SD card from your PC and insert it into the SD card slot of the VAR-DT410CustomBoard
+*Remove the SD card from your PC and insert it into the SD card slot of the VAR-SD410CustomBoard
-*Set Boot Select switch (SW3) to the ON position. This tells the DART-SD410 to boot from external SD card.
+*Set Boot Select switch (SW3) to the ON position. This directs the DART-SD410 to boot from an external SD card. After this step, the system will read the image from the external SD card and boot into Debian.
-*Cycle the power of the VAR-DT410CustomBoard
+*Connect VAR-SD410CustomBoard to a PC using the USB cable. Please pay attention to use the Debug USB connector (J21). A new COM port should be found on a PC.
-After this step the system will read the image from external SD card and boot into a fastboot mode.
+*Open any terminal to a newly created com port using 115200,8,n,1 settings.
-Now you are ready to burn the correct partiotion table.
+*Power up the board.
-*Navigate to the RescueImages folder of the choosen OS
+*Navigate to /media/Linaro/OSes/Android or /media/Linaro/OSes/Debian directory.
-*Run '''flashall''' script
+<pre>
-*Set Boot Select switch (SW3) to the OFF position. This tells the DART-SD410 to boot from internal eMMC device.
+# cd /media/linaro/OSes/Android
-*Cycle the power of the VAR-DT410CustomBoard
+or
+# cd /media/linaro/OSes/Debian
+</pre>
+*Execute update.sh script.
+<pre>
+# ./update.sh
+</pre>
+*Let the script finish the update process.
+*Remove the SD
+*Cycle the power of VAR-SD410CustomBoard.
 The needed OS will start
-= Start using your VAR-DT410CustomBoard =
+{{note| NOTE:<br>
+To get the most updated images it is suggested to use fastboot and precompiled images to upgrade to the latest version|info}}
+{{note| NOTE:<br>
+There are many error messages occure on DART-SD410 that is coming without Wi-Fi assembled. The Wi-Fi driver should be removed from the SD Card in this case:|info}}
+<pre>
+# rm /lib/modules/4.9.56-linaro-lt-qcom/kernel/drivers/remoteproc/qcom_wcnss_pil.ko
+# reboot
+</pre>
+= Start using your VAR-SD410CustomBoard =
 *Upack the contents of the package
-*Veryfy that the DART-SD410 SoM is connected properly into VAR-DT410CustomBoard card
+*Veryfy that the DART-SD410 SoM is connected properly into VAR-SD410CustomBoard card
 *Connect the screen LVDS cable to the LCD (the red wires should be at pin 1 position)
-*Connect the other side of the cable to VAR-DT410CustomBoard J11 (the red wires should be at pin 1 position i.e. closer to HDMI connector)
+*Connect the other side of the cable to VAR-SD410CustomBoard J11 (the red wires should be at pin 1 position i.e. closer to HDMI connector)
 *Connect the touch screen flat cable to J4 (the copper contacts should face PCB card)
 *Connect USB cable to a PC
-*Connect the Micro USB plug to VAR-DT410CustomBoard J21. Wait for USB device enumeration and driver installation
+*Connect the Micro USB plug to VAR-SD410CustomBoard J21. Wait for USB device enumeration and driver installation
 *Open any serial port console program (we suggest using [http://www.putty.org Putty]) and set it to 115200,8,1,n baudrate
 *Plug in the power supply to 100/220V
 {{note| NOTE:<br>If Camera adapter was purchased then it should be plugged in before the first power up. Otherwise the Android will remove Camera program and it will not be accessible untill system re-flash|info}}
-*Plug in the power adapter 5V to VAR-DT410CustomBoard J18
+*Plug in the power adapter 5V to VAR-SD410CustomBoard J18
 Immideately the serial console will show the booting process and
 after about a minute the LCD will show the boot animation and Android will be started
 {{note| NOTE:<br>The first Boot up of the Android takes more time because of database initialization|info}}
+{{note| NOTE:<br>Please remove SD card from the slop before boot|info}}
-= Switching display options =
+= Switching display options in Android =
 To switch between LCD and HDMI the following fastboot commands should be run
 ==To switch to HDMI==

DART-SD410 Android Getting Started: Difference between revisions