Yocto Build U-Boot: Difference between revisions
From Variscite Wiki
m (1 revision imported: Import of additions after the 20th of May 2020) |
No edit summary |
||
| Line 134: | Line 134: | ||
{{#ifeq: {{#var:SOC_FAMILY}}|imx8| | {{#ifeq: {{#var:SOC_FAMILY}}|imx8| | ||
{{#ifeq: {{#var:SOC}}|mx8qxp| | |||
Build boot image for B0 SOC revision: | |||
$ make -f soc.mak clean | |||
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} REV=B0 MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl | |||
$ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}} | |||
<br> | |||
Build boot image for C0 SOC revision: | |||
$ make -f soc.mak clean | |||
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} REV=C0 MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl | |||
$ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}} | |||
| | |||
Build boot image: | Build boot image: | ||
$ make -f soc.mak clean | $ make -f soc.mak clean | ||
$ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl | $ make -f soc.mak SOC={{#var:IMX_MKIMAGE_SOC}} MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh flash_spl | ||
$ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}} | $ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}} | ||
}} | |||
| | | | ||
{{#ifeq: {{#var:SOC}}|mx8mq| | {{#ifeq: {{#var:SOC}}|mx8mq| | ||
Revision as of 12:43, 15 June 2020
Yocto Build U-Boot from source code
Toolchain installation for out of Yocto builds
To install the toolchain, follow Yocto Toolchain installation.
Build U-Boot out of Yocto tree
Obtain sources:
$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03 $ cd uboot-imx
Configure compilation environment:
$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi
Cleanup everything:
$ make mrproper
Select one of the following configurations:
For booting from SD card/eMMC: $ make mx6var_som_sd_defconfig For booting from NAND flash: $ make mx6var_som_nand_defconfig
Build U-Boot:
$ make -j4
Install the built U-Boot on an SD card
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync $ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync (Replace /dev/sdX with the correct device)
If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:
$ sudo cp SPL /media/rootfs/opt/images/... $ sudo cp u-boot.img /media/rootfs/opt/images/...
And eject the SD card gracefully from host machine.
Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)
Update your U-Boot out of Yocto tree
$ git pull