Yocto Build U-Boot: Difference between revisions
From Variscite Wiki
No edit summary |
No edit summary |
||
| Line 55: | Line 55: | ||
Download SECO firmware: | Download SECO firmware: | ||
{{#ifeq: {{#var:HARDWARE_NAME}} | VAR-SOM-MX8X | {{#ifeq: {{#var:MACHINE_NAME_B0}} | imx8qxpb0-var-som | | |||
$ wget {{#var:SECO_FIRMWARE_URL}}/{{#var:SECO_FIRMWARE}}.bin | |||
$ chmod +x {{#var:SECO_FIRMWARE}}.bin | |||
$ ./{{#var:SECO_FIRMWARE}}.bin | |||
$ cp {{#var:SECO_FIRMWARE}}/firmware/seco/mx8qx*-ahab-container.img . | |||
| | |||
$ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin | $ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin | ||
$ chmod +x {{#var:NXP_FIRMWARE}}.bin | $ chmod +x {{#var:NXP_FIRMWARE}}.bin | ||
$ ./{{#var:NXP_FIRMWARE}}.bin | $ ./{{#var:NXP_FIRMWARE}}.bin | ||
$ cp {{#var:NXP_FIRMWARE}}/firmware/seco/{{#var:SECO_FIRMWARE}} . | $ cp {{#var:NXP_FIRMWARE}}/firmware/seco/{{#var:SECO_FIRMWARE}} . | ||
}} | |||
| | |||
$ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin | |||
$ chmod +x {{#var:NXP_FIRMWARE}}.bin | |||
$ ./{{#var:NXP_FIRMWARE}}.bin | |||
$ cp {{#var:NXP_FIRMWARE}}/firmware/seco/{{#var:SECO_FIRMWARE}} . | |||
}} | |||
| | | | ||
Download DDR {{#ifeq: {{#var:SOC}}|mx8mq|and HDMI|}} firmware: | Download DDR {{#ifeq: {{#var:SOC}}|mx8mq|and HDMI|}} firmware: | ||
Revision as of 11:50, 22 April 2020
Yocto Build U-Boot from source code
Toolchain installation for out of Yocto builds
To install the toolchain, follow Yocto Toolchain installation.
Build U-Boot out of Yocto tree
Obtain sources:
$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03 $ cd uboot-imx
Configure compilation environment:
$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi
Cleanup everything:
$ make mrproper
Select one of the following configurations:
For booting from SD card/eMMC: $ make mx6var_som_sd_defconfig For booting from NAND flash: $ make mx6var_som_nand_defconfig
Build U-Boot:
$ make -j4
Install the built U-Boot on an SD card
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync $ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync (Replace /dev/sdX with the correct device)
If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:
$ sudo cp SPL /media/rootfs/opt/images/... $ sudo cp u-boot.img /media/rootfs/opt/images/...
And eject the SD card gracefully from host machine.
Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)
Update your U-Boot out of Yocto tree
$ git pull