DART-MX8M suspend: Difference between revisions

From Variscite Wiki
(Created page with "{{PageHeader|Suspend to RAM}} {{DocImage|category1=Yocto|category2=DART-MX8M}} = Suspend to RAM = This state offers significant power savings as everything in the system is p...")
 
No edit summary
Line 4: Line 4:


This state offers significant power savings as everything in the system is put into a low-power state, except for memory, which is placed into the self-refresh mode to retain its contents.<br>
This state offers significant power savings as everything in the system is put into a low-power state, except for memory, which is placed into the self-refresh mode to retain its contents.<br>


To suspend to RAM:
To suspend to RAM:
Line 30: Line 29:
  };
  };


= Measuring current consumption in suspend =
- Pressing the capacitive touch which has the boolean property "wakeup-source" set in its device tree node, e.g.:
To measure the current remove resistor R15 and connect ampere meter instead.<br>
 
        ft5x06_ts: ft5x06_ts@38 {
                status = "disabled";
                compatible = "edt,edt-ft5x06";
                reg = <0x38>;
                reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
                pinctrl-names = "default";
                pinctrl-0 = <&pinctrl_touch>;
                interrupt-parent = <&gpio1>;
                interrupts = <14 0>;
                touchscreen-size-x = <800>;
                touchscreen-size-y = <480>;
                touchscreen-inverted-x;
                touchscreen-inverted-y;
                '''wakeup-source''';
        };
 
= Measuring SOM current consumption in suspend =
To measure SOM current consumption remove resistor R15 and connect ampere meter instead.<br>
It is recommended to boot from eMMC to get accurate measurement.
It is recommended to boot from eMMC to get accurate measurement.

Revision as of 12:18, 15 July 2018

Suspend to RAM

Suspend to RAM

This state offers significant power savings as everything in the system is put into a low-power state, except for memory, which is placed into the self-refresh mode to retain its contents.

To suspend to RAM:

$ pm-suspend

Wake up

There are many possible ways to wake up from suspend.
A few examples:
- Pushing the ON/OFF button (when present on the board)
- Pushing a button on the board which has the boolean property "wakeup-source" set in its device tree node (under gpio_keys), e.g.:

	gpio-keys {
		compatible = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_gpio_keys>;
               ...
               back {
                       label = "Back";
                       gpios = <&gpio4 6 GPIO_ACTIVE_LOW>;
                       linux,code = <KEY_BACK>;
                       wakeup-source;
               };
	};

- Pressing the capacitive touch which has the boolean property "wakeup-source" set in its device tree node, e.g.:

       ft5x06_ts: ft5x06_ts@38 {
               status = "disabled";
               compatible = "edt,edt-ft5x06";
               reg = <0x38>;
               reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
               pinctrl-names = "default";
               pinctrl-0 = <&pinctrl_touch>;
               interrupt-parent = <&gpio1>;
               interrupts = <14 0>;
               touchscreen-size-x = <800>;
               touchscreen-size-y = <480>;
               touchscreen-inverted-x;
               touchscreen-inverted-y;
               wakeup-source;
       };

Measuring SOM current consumption in suspend

To measure SOM current consumption remove resistor R15 and connect ampere meter instead.
It is recommended to boot from eMMC to get accurate measurement.