Yocto Build U-Boot

From Variscite Wiki
Yocto Build U-Boot from source code

Toolchain installation for out of Yocto builds

To install the toolchain, follow the Yocto Toolchain installation guide.

Build U-Boot out of Yocto tree

Obtain sources:

$ git clone https://github.com/varigit/uboot-imx.git -b lf_v2021.04_var03
$ cd uboot-imx

Configure compilation environment:

$ source /opt/b2qt/3.3/environment-setup-aarch64-poky-linux

Cleanup everything:

$ make mrproper


Select configuration:

$ make imx8mp_var_dart_defconfig

Build U-Boot:

$ make -j$(nproc)

Build boot image

The final boot image contains multiple firmware files, as explained by NXP in IMX_LINUX_USERS_GUIDE.pdf (Search for "How to build imx-boot image by using imx-mkimage").

The following procedure builds the final image:

Create imx-boot-tools directory:

$ mkdir imx-boot-tools
$ cd imx-boot-tools

Download DDR firmware:

$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.14.bin
$ chmod +x firmware-imx-8.14.bin
$ ./firmware-imx-8.14.bin
$ cp firmware-imx-8.14/firmware/ddr/synopsys/* .

Download imx_mkimage:

$ git clone https://github.com/nxp-imx/imx-mkimage -b lf-5.10.72_2.2.0
$ cp imx-mkimage/iMX8M/*.c imx-mkimage/iMX8M/*.sh  imx-mkimage/scripts/*.sh .
$ cp dtb_check.sh ../scripts/

Download and build ATF:

$ git clone https://github.com/varigit/imx-atf -b lf_v2.4_var04 
$ git clone https://github.com/varigit/meta-variscite-bsp -b hardknott
$ cd imx-mkimage

$ git apply ../meta-variscite-bsp/recipes-bsp/imx-mkimage/imx-boot/0001-iMX8M-soc-allow-dtb-override.patch
$ git apply ../meta-variscite-bsp/recipes-bsp/imx-mkimage/imx-boot/0002-iMX8M-soc-change-padding-of-DDR4-and-LPDDR4-DMEM-fir.patch $ cp iMX8M/soc.mak .. $ cd .. $ cd imx-atf $ source /opt/b2qt/3.3/environment-setup-aarch64-poky-linux $ unset LDFLAGS $ make PLAT=imx8mp bl31 $ cp build/imx8mp/release/bl31.bin .. $ cd ..

Copy U-Boot binaries:

$ cp ../tools/mkimage mkimage_uboot
$ cp ../u-boot.bin .
$ cp ../u-boot-nodtb.bin ../spl/u-boot-spl.bin ../arch/arm/dts/imx8mp-var-dart-dt8mcustomboard.dtb ../arch/arm/dts/imx8mp-var-som-symphony.dtb .

Build boot image:

$ make -f soc.mak clean
$ make -f soc.mak  SOC=iMX8MP  dtbs="imx8mp-var-dart-dt8mcustomboard.dtb  imx8mp-var-som-symphony.dtb"  MKIMG=./mkimage_imx8 PAD_IMAGE=./pad_image.sh  CC=gcc OUTIMG=imx-boot-sd.bin flash_evk 

Install the built U-Boot on an SD card


$ sudo dd if=imx-boot-sd.bin of=/dev/sdX bs=1K seek=32 conv=fsync

(Replace /dev/sdX with the correct device)

If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:

$ sudo cp imx-boot-sd.bin /media/rootfs/opt/images/…

And eject the SD card gracefully from host machine.


Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)

Update your U-Boot out of Yocto tree

$ git pull