Linux USB OTG: Difference between revisions

From Variscite Wiki
(Fix imx8mm, imx8mq dts files for new kernels)
Line 53: Line 53:
{{#ifeq: {{#var:HARDWARE_NAME}} | DART-MX8M |
{{#ifeq: {{#var:HARDWARE_NAME}} | DART-MX8M |
<pre>
<pre>
# cat /sys/firmware/devicetree/base/usb@38100000/dwc3/dr_mode; echo
# cat /sys/firmware/devicetree/base/usb@38100000/dwc3/dr_mode;
</pre>
</pre>
|
|
{{#ifeq: {{#var:HARDWARE_NAME}} | DART-MX8M-PLUS |
{{#ifeq: {{#var:HARDWARE_NAME}} | DART-MX8M-PLUS |
<pre>
<pre>
# cat /sys/firmware/devicetree/base/usb@32f10100/dwc3@38100000/dr_mode; echo
# cat /sys/firmware/devicetree/base/usb@32f10100/dwc3@38100000/dr_mode;
</pre>
</pre>
|
|
<pre>
<pre>
# cat /sys/firmware/devicetree/base/usb@32e40000/dr_mode; echo
# cat /sys/firmware/devicetree/base/usb@32e40000/dr_mode;
</pre>
</pre>
}}}}
}}}}

Revision as of 20:27, 2 June 2022

DART-MX8M USB OTG

Configuring the USB OTG port under Linux

By default, the USB OTG port is configured as OTG in the device tree, and a USB type-C receptacle is assembled on the DART-MX8M custom board.
To use it as host only or peripheral only you need to change the value of the dr_mode property under the USB node in the device tree.
dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg"

For example:
Follow either the "Build the Linux kernel from source code" or "Customizing the Linux kernel" Wiki pages and edit the following device tree file:
arch/arm64/boot/dts/freescale/fsl-imx8mq-var-dart-common.dtsi

&usb_dwc3_0 {
	status = "okay";
	extcon = <&typec_ptn5150>;
-	dr_mode = "otg";
+	dr_mode = "host";
};

If you build the kernel manually from source code, you should build only the device trees and copy them to your SD card or eMMC.

Note: You can read the current dr_mode value on a running target, by executing the following command:

# cat /sys/firmware/devicetree/base/usb@38100000/dwc3/dr_mode;

Using the USB OTG port under Linux

As host (default)

USB host

As peripheral

In order to use the board as a peripheral, an appropriate module needs to be loaded.
For example, there is an Ethernet gadget module called g_ether, a mass storage gadget called g_mass_storage, a serial gadget called g_serial, etc.

Example using the g_mass_storage module to expose the root partition on eMMC to a PC while booting from recovery SD card:
Connect a type-C plug to Standard-A plug cable between the board and a PC, and run the following on the board:

# umount /dev/mmcblk0p1
# modprobe g_mass_storage file=/dev/mmcblk0p1

The partition should be loaded on the PC as a mass storage device.

As OTG

With OTG, the board can be either a host, or a peripheral.
In order to use it as a host and connect a peripheral (e.g. a USB flash drive) to it, either use a peripheral with type-C connector or use type-C to type-A adapter.
In order to use it as a peripheral and connect it to a PC, for example, a cable with a type-C plug on one end and a Standard-A plug on the other is needed.