Yocto Build U-Boot: Difference between revisions

From Variscite Wiki
No edit summary
Line 60: Line 60:
  $ cp {{#var:NXP_FIRMWARE}}/firmware/seco/{{#var:SECO_FIRMWARE}} .
  $ cp {{#var:NXP_FIRMWARE}}/firmware/seco/{{#var:SECO_FIRMWARE}} .
|
|
<br>
Download DDR and HDMI firmware
Download DDR and HDMI firmware
  $ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin
  $ wget {{#var:NXP_FIRMWARE_URL}}/{{#var:NXP_FIRMWARE}}.bin
Line 70: Line 69:


{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
<br>
Download and build imx_mkimage
Download and build imx_mkimage
  $ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}}
  $ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}}
Line 78: Line 76:
  $ cd ..
  $ cd ..
|
|
<br>
Download imx_mkimage
Download imx_mkimage
  $ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}}
  $ git clone {{#var:NXP_IMX_GIT}}/imx-mkimage -b {{#var:NXP_IMX_BRANCH}}
Line 101: Line 98:
   
   
{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
{{#ifeq: {{#var:SOC_FAMILY}}|imx8|
<br>
Build boot image
Build boot image
  $ make -f soc.mak clean
  $ make -f soc.mak clean
Line 107: Line 103:
  $ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
  $ mv flash.bin {{#var:U-BOOT_SD_IMAGE_NAME}}
|
|
<br>
Build boot image
Build boot image
  $ make -f soc.mak clean  
  $ make -f soc.mak clean  

Revision as of 17:59, 20 June 2019

Yocto Build U-Boot from source code

Toolchain installation for out of Yocto builds

To install the toolchain, follow Yocto Toolchain installation.

Build U-Boot out of Yocto tree

Obtain sources:

$ git clone https://github.com/varigit/uboot-imx.git -b imx_v2015.04_4.1.15_1.1.0_ga_var03
$ cd uboot-imx

Configure compilation environment:

$ source /opt/fslc-x11/2.2.1/environment-setup-armv7at2hf-neon-fslc-linux-gnueabi

Cleanup everything:

$ make mrproper

Select one of the following configurations:

For booting from SD card/eMMC:
$ make mx6var_som_sd_defconfig

For booting from NAND flash:
$ make mx6var_som_nand_defconfig

Build U-Boot:

$ make -j4


Install the built U-Boot on an SD card


$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1; sync
$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69; sync
(Replace /dev/sdX with the correct device)

If you want to use our recovery SD card to flash the built U-Boot to NAND flash/eMMC, then copy it to the appropriate location in the SD card:

$ sudo cp SPL /media/rootfs/opt/images/... 
$ sudo cp u-boot.img /media/rootfs/opt/images/...

And eject the SD card gracefully from host machine.


Note: If you manually upgrade an existing U-Boot, and you have an old environment saved, it is a good idea to reset your environment to the new default (see Environment handling commands)

Update your U-Boot out of Yocto tree

$ git pull