DART-6UL/VAR-SOM-MX7 Wireless LAN

From Variscite Wiki
Revision as of 13:19, 25 August 2019 by Admin (talk | contribs)
DART-6UL/VAR-SOM-MX7 Wireless LAN

Test

Scan for wireless networks:

$ ifconfig wlan0 up
$ iw dev wlan0 scan | grep SSID


Connecting to a WPA encrypted network:
If you are using Krogoth distro, please remember that Wifi interface is controlled by connman.
Before continuing with this procedure, remember to disable wifi control running

$ connmanctl disable wifi

If you are using Debian, please note that Wifi interface is controlled by Network Manager.
Before continuing with this procedure, remember to disable wifi control running

$ nmcli radio wifi off

Find your network from the above scan command.

$ mv /etc/wpa_supplicant.conf /etc/wpa_supplicant.conf.org
$ wpa_passphrase <YourAP> <YourPassword> >/etc/wpa_supplicant.conf
$ wpa_supplicant -B -Dnl80211 -iwlan0 -c/etc/wpa_supplicant.conf

Check link:

$ iw dev wlan0 link

Disable eth0:

$ ifconfig eth0 down
$ ifconfig eth1 down

Run DHCP:

$ udhcpc -iwlan0
$ ifconfig

Check link speed:
iperf3 server (on Target/Host):

$ ifconfig  (to get the IP address)
$ iperf3 -s

iperf3 client (on Host/Target):

$ iperf3 -c <IP_ADDRESS_OF_IPERF_SERVER>


Useful link for common iw commands: https://wiki.archlinux.org/index.php/Wireless_network_configuration#Manual_setup

Access Point

This example will demonstrate you how to use the board as an access point. It will forward packets from wlan0 to eth0. DHCPD:

$ vi /etc/udhcpd.conf 
# Sample udhcpd configuration file (/etc/udhcpd.conf)
# The start and end of the IP lease block
start           192.168.5.20    #default: 192.168.0.20
end             192.168.5.25    #default: 192.168.0.254
# The interface that udhcpd will use
interface   wlan0               #default: eth0
#Example
opt     dns     8.8.8.8  8.8.4.4 # public google dns servers
option  subnet  255.255.255.0
opt     router  192.168.5.1
option  lease   864000          # 10 days of seconds

This is a network example. You need to set the IP address based on your network.

Wireless configuration can be setup in file /etc/hostapd.conf before launching hostapd for configuring access point name, requiring password, etc.
For example:

$ vi /etc/hostapd.conf
You can set the following parameters:
ssid=VARI_AP
wpa=2
rsn_pairwise=CCMP
wpa_passphrase=12345678
wpa_key_mgmt=WPA-PSK

Ensure that wpa_supplicant is not holding the device

$ killall wpa_supplicant
$ killall hostapd

IP Forwarding:

$ echo 1 > /proc/sys/net/ipv4/ip_forward
$ ifconfig wlan0 192.168.5.1
$ hostapd -B /etc/hostapd.conf -P /var/run/hostapd.pid
$ udhcpd /etc/udhcpd.conf
$ iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

As a next step one should take a look at iw utility which can be used for configuring some parameters https://wireless.wiki.kernel.org/en/users/documentation/iw